Rubber covered wire

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Rubber covered wire

radiorich
Phorum Expert

Posts: 1,597
Threads: 100
Joined: May 2008
City: Omak State, Province, Country: WA

09-26-2010, 02:36 AM

Hello Joe,
I too use heat shrink but in sets like the airline I'm working on for a customer I'm also using some new color pvc wire to replace some of the old .
Far as shrinking it I use a heatgun made for shrinking heatshrink made by MASTER APPLIANCE it even comes with a nozzle that ruduces the opening to allow to heat in small area .

Rich
P.S. Ron I sure like you Aladdin lamp I have a few like that would be found on waltons or little house in the praier.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Rubber covered wire - by w4rtc - 09-24-2010, 04:02 PM

Re: Rubber covered wire - by exray - 09-24-2010, 05:40 PM

Re: Rubber covered wire - by BDM - 09-25-2010, 09:58 AM

Re: Rubber covered wire - by Ron Ramirez - 09-25-2010, 10:16 AM

Re: Rubber covered wire - by BDM - 09-25-2010, 10:25 AM

Re: Rubber covered wire - by Ron Ramirez - 09-25-2010, 10:34 AM

Re: Rubber covered wire - by BDM - 09-25-2010, 10:45 AM

Re: Rubber covered wire - by DeckApe - 09-25-2010, 05:14 PM

Re: Rubber covered wire - by radiorich - 09-26-2010, 02:36 AM

Re: Rubber covered wire - by w4rtc - 09-26-2010, 11:00 PM

Re: Rubber covered wire - by radiorich - 09-27-2010, 12:25 AM

Re: Rubber covered wire - by DeckApe - 10-02-2010, 11:40 AM

Re: Rubber covered wire - by Ron Ramirez - 10-03-2010, 09:39 AM

Re: Rubber covered wire - by w4rtc - 10-07-2010, 11:55 PM

Re: Rubber covered wire - by radiorich - 10-12-2010, 02:39 PM

Re: Rubber covered wire - by codefox1 - 10-12-2010, 05:26 PM

Re: Rubber covered wire - by Ron Ramirez - 10-12-2010, 06:39 PM

Re: Rubber covered wire - by exray - 10-12-2010, 07:48 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me