Emerson 25A restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Emerson 25A restoration

klondike98
Phorum Moderator

Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

09-02-2018, 09:23 PM

Unfortunately the power supply choke is open on this set. It has had some previous work done to it.

[Image: https://www.dropbox.com/s/wryjchvk05soox....jpg?raw=1]

I peeled back some of paper and found the connection to lug was bad.

[Image: https://www.dropbox.com/s/cbzkb27c1ofyfx....jpg?raw=1]

Slpliced it and now have continuity but it is reading 400k ohms which seems too high for a choke. Am looking for some additional info on this choke but so far have not found it.

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Emerson 25A restoration - by klondike98 - 08-30-2018, 10:18 PM

RE: Emerson 25A restoration - by Radioroslyn - 08-30-2018, 11:26 PM

RE: Emerson 25A restoration - by Paul Philco322 - 08-31-2018, 12:06 PM

RE: Emerson 25A restoration - by klondike98 - 08-31-2018, 12:20 PM

RE: Emerson 25A restoration - by Eliot Ness - 08-31-2018, 12:40 PM

RE: Emerson 25A restoration - by morzh - 08-31-2018, 01:19 PM

RE: Emerson 25A restoration - by Radioroslyn - 08-31-2018, 02:58 PM

RE: Emerson 25A restoration - by klondike98 - 08-31-2018, 06:48 PM

RE: Emerson 25A restoration - by klondike98 - 09-02-2018, 09:23 PM

RE: Emerson 25A restoration - by klondike98 - 09-05-2018, 10:28 PM

RE: Emerson 25A restoration - by Radioroslyn - 09-06-2018, 10:34 AM

RE: Emerson 25A restoration - by klondike98 - 09-06-2018, 12:37 PM

RE: Emerson 25A restoration - by klondike98 - 07-08-2019, 10:21 AM

RE: Emerson 25A restoration - by Eliot Ness - 07-08-2019, 11:01 AM

RE: Emerson 25A restoration - by mikethedruid - 07-08-2019, 04:11 PM

RE: Emerson 25A restoration - by OldRestorer - 07-09-2019, 12:09 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me