Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Paint stripper
#28

I bought some 600G 3M wet/dry paper from epay and think I got a fair deal or it. Most retailers are getting abt $1 a sheet (8 1/2x11"). I paid abt 50c per sheet. When looking at the listing be sure to check the size of the sheet (some sell half sheets 8 1/2x 5 1/2) and quantity. It's a little bit of a numbers game. Ended up w/ 50 sheets for $25 free shipping.
Have been using these guys for the Mohawk supplies: https://www.westlunddistributing.com/tou...ducts.html Online catalog is a pita to try to find anything so I get the Mohawk product #s form another site. I think the pricing is pretty good @ $5.88 per can. Would recommend getting abt 1/2 dozen different products to get started. Those being:
Sanding Sealer M 102-0423
Gloss M 102-0420
No Blush M 103-0475
Med Wlnt M 100-0207
Drk Wlnt M 100-0351
Ex Drk Wlnt M 100-0209
Grain fllr M 608-4226
The sanding sealer and gloss I tend to go thru pretty quick maybe 4 of ea. No Blush will last forever (1), when you need it it's a miracle worker! And two cans each of the walnut toners. The jury seems to be out on the grain filler some like other brands so there maybe better one out there. I mostly got it here for convince.


Good Luck

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Paint stripper - by 45philcodon - 01-05-2018, 04:03 PM
RE: Paint stripper - by rfeenstra - 01-05-2018, 05:36 PM
RE: Paint stripper - by 45philcodon - 01-05-2018, 06:47 PM
RE: Paint stripper - by Arran - 01-06-2018, 02:06 AM
RE: Paint stripper - by tbone - 02-14-2018, 07:36 PM
RE: Paint stripper - by Phlogiston - 02-15-2018, 11:38 AM
RE: Paint stripper - by Paul Philco322 - 02-15-2018, 09:09 PM
RE: Paint stripper - by tbone - 02-16-2018, 09:26 PM
RE: Paint stripper - by doug-5er - 02-26-2018, 09:21 PM
RE: Paint stripper - by oscartg - 05-18-2018, 12:24 PM
RE: Paint stripper - by Phlogiston - 05-18-2018, 12:45 PM
RE: Paint stripper - by John Bartley - 05-18-2018, 03:11 PM
RE: Paint stripper - by tbone - 05-19-2018, 08:04 AM
RE: Paint stripper - by 45philcodon - 05-20-2018, 05:23 PM
RE: Paint stripper - by Greggshere - 09-01-2018, 09:37 PM
RE: Paint stripper - by tbone - 09-02-2018, 06:06 PM
RE: Paint stripper - by Phlogiston - 09-02-2018, 08:02 PM
RE: Paint stripper - by Ron Ramirez - 09-02-2018, 09:57 PM
RE: Paint stripper - by Arran - 09-03-2018, 04:45 AM
RE: Paint stripper - by Greggshere - 09-10-2018, 11:15 AM
RE: Paint stripper - by Phlogiston - 09-10-2018, 03:59 PM
RE: Paint stripper - by Greggshere - 09-10-2018, 04:31 PM
RE: Paint stripper - by Phlogiston - 09-10-2018, 07:29 PM
RE: Paint stripper - by Arran - 09-11-2018, 03:46 AM
RE: Paint stripper - by Greggshere - 09-11-2018, 11:01 AM
RE: Paint stripper - by Phlogiston - 09-11-2018, 12:29 PM
RE: Paint stripper - by Greggshere - 09-11-2018, 04:52 PM
RE: Paint stripper - by Radioroslyn - 09-11-2018, 06:51 PM
RE: Paint stripper - by Phlogiston - 09-11-2018, 07:39 PM
RE: Paint stripper - by Ron Ramirez - 09-11-2018, 07:58 PM
RE: Paint stripper - by Radioroslyn - 09-11-2018, 08:14 PM
RE: Paint stripper - by Greggshere - 09-12-2018, 12:33 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM

[-]
Who's Online
There are currently no members online.

>