Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

A Philco 91B
#6

Finally getting back to the 91B cabinet.  I had it stripped back in Dec 2017 but am just now getting a chance to spray in between the rain drops...

I did a light coat of medium brown walnut ultra classic mohawk over the entire cabinet except the trim and front panel the other day...
[Image: https://www.dropbox.com/s/xgme5gjmhh6vol....jpg?raw=1]

and then did the trim with extra dark walnut ultra classic mohawk  and also with a very light dose of it on the front panel.

[Image: https://www.dropbox.com/s/unwhx0bf67k6ic....jpg?raw=1]


Messages In This Thread
A Philco 91B - by klondike98 - 12-13-2017, 11:45 AM
RE: A Philco 91B - by Phlogiston - 12-13-2017, 12:02 PM
RE: A Philco 91B - by Arran - 12-14-2017, 04:46 AM
RE: A Philco 91B - by Steve Davis - 12-14-2017, 10:33 AM
RE: A Philco 91B - by Phlogiston - 12-16-2017, 11:16 AM
RE: A Philco 91B - by klondike98 - 10-01-2018, 03:29 PM
RE: A Philco 91B - by Radioroslyn - 10-01-2018, 08:31 PM
RE: A Philco 91B - by Greggshere - 10-06-2018, 10:26 PM
RE: A Philco 91B - by klondike98 - 11-01-2018, 02:01 PM
RE: A Philco 91B - by KCMike - 11-01-2018, 03:34 PM
RE: A Philco 91B - by klondike98 - 11-12-2018, 08:32 PM
RE: A Philco 91B - by klondike98 - 11-13-2018, 02:07 PM
RE: A Philco 91B - by OldRestorer - 11-14-2018, 08:45 AM
RE: A Philco 91B - by morzh - 11-14-2018, 02:42 PM
RE: A Philco 91B - by Ron Ramirez - 11-14-2018, 03:33 PM
RE: A Philco 91B - by morzh - 11-14-2018, 03:50 PM
RE: A Philco 91B - by klondike98 - 11-14-2018, 04:30 PM
RE: A Philco 91B - by klondike98 - 11-15-2018, 04:38 PM
RE: A Philco 91B - by KCMike - 11-15-2018, 06:03 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>