8G005 Zenith T/O Restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

8G005 Zenith T/O Restoration

klondike98
Phorum Moderator

Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

#24

10-04-2018, 09:54 PM

If I remember correctly those coils and they seemed pretty fragile to me at the time. I think I checked to make sure that I was receiving something from my signal generator with audio modulation on each of the bands and that it was close to the frequency on the radio's dial. I did use a small screw driver to align one or two bands but they seemed right on so I did not go farther.

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

8G005 Zenith T/O Restoration - by morzh - 09-01-2018, 07:26 PM

RE: 8G005 Zenith T/O Restoration - by klondike98 - 09-02-2018, 09:08 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 09-02-2018, 11:12 PM

RE: 8G005 Zenith T/O Restoration - by Arran - 09-03-2018, 02:37 AM

RE: 8G005 Zenith T/O Restoration - by morzh - 09-03-2018, 05:10 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 09-10-2018, 09:05 AM

RE: 8G005 Zenith T/O Restoration - by morzh - 09-24-2018, 10:56 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 09-30-2018, 09:21 PM

RE: 8G005 Zenith T/O Restoration - by PhilcoJohn - 10-01-2018, 07:50 AM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-01-2018, 08:05 AM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-01-2018, 10:28 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-02-2018, 08:20 PM

RE: 8G005 Zenith T/O Restoration - by Paul Philco322 - 10-02-2018, 08:27 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-02-2018, 08:34 PM

RE: 8G005 Zenith T/O Restoration - by KCMike - 10-02-2018, 09:27 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-02-2018, 10:06 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-03-2018, 08:06 PM

RE: 8G005 Zenith T/O Restoration - by sam - 10-03-2018, 10:53 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-03-2018, 11:01 PM

RE: 8G005 Zenith T/O Restoration - by sam - 10-03-2018, 11:19 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-03-2018, 11:34 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-04-2018, 03:41 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-04-2018, 07:58 PM

RE: 8G005 Zenith T/O Restoration - by klondike98 - 10-04-2018, 09:54 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-04-2018, 10:34 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 10-05-2018, 10:10 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 11-29-2018, 10:01 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 12-08-2018, 07:34 PM

RE: 8G005 Zenith T/O Restoration - by morzh - 12-08-2018, 08:44 PM

RE: 8G005 Zenith T/O Restoration - by klondike98 - 12-09-2018, 11:12 AM

RE: 8G005 Zenith T/O Restoration - by morzh - 12-09-2018, 11:39 AM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
12' Philco
GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt. The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM

Who's Online

There are currently 5133 online users. [Complete List]
» 1 Member(s) | 5132 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me