1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 66B restoration
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#22

10-06-2018, 04:30 PM
Its raining again so no lacquer spraying today...

The 66 has a board with a variety of caps and resistors mounted to 14 connector/lugs.  I had read a previous restoration write-up that said you might as well just resign yourself to taking the board off since there are caps under it that you can't reach without doing so.  I chose to stuff all the bakelite caps first which went just fine.  A 1 meg dogbone was reproduced and replaced along the way (there will be others later) and then I started on the board.  I drew out what I could see and then started desoldering leads starting at one end and working my way around.  Once I thought I had it completely disconnected....I was wrong...several more unnoticed connection needed to come off and finally the board could come out...

[Image: https://www.dropbox.com/s/2m1wz2vtkcbdq4....jpg?raw=1]

(sorry...looks like I was a little shaky taking the photo Icon_redface ) the big 2 watt 37k (orange-violet-orange) resistor is reading 46k so I will probably replace that.  The 100k (white-white-orange) resistors are reading 80k and the 70k (violet-black-orange) resistors are measuring 60k so I will probably just leave them alone.  The 500k (yellow-white-yellow) is reading 880k so it will be replaced also.  All the paper caps will get stuffed.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 66B restoration - by klondike98 - 09-24-2018, 07:08 PM
RE: Philco 66B restoration - by morzh - 09-24-2018, 07:15 PM
RE: Philco 66B restoration - by klondike98 - 09-24-2018, 07:24 PM
RE: Philco 66B restoration - by Arran - 09-25-2018, 04:18 AM
RE: Philco 66B restoration - by morzh - 09-25-2018, 07:51 AM
RE: Philco 66B restoration - by klondike98 - 09-25-2018, 05:49 PM
RE: Philco 66B restoration - by morzh - 09-25-2018, 07:15 PM
RE: Philco 66B restoration - by klondike98 - 09-26-2018, 09:17 AM
RE: Philco 66B restoration - by morzh - 09-26-2018, 11:47 AM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 12:21 PM
RE: Philco 66B restoration - by morzh - 09-27-2018, 03:22 PM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 07:46 PM
RE: Philco 66B restoration - by Ron Ramirez - 09-27-2018, 07:59 PM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 08:09 PM
RE: Philco 66B restoration - by morzh - 09-27-2018, 10:08 PM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 10:42 PM
RE: Philco 66B restoration - by klondike98 - 09-28-2018, 02:30 PM
RE: Philco 66B restoration - by morzh - 09-28-2018, 02:38 PM
RE: Philco 66B restoration - by Radioroslyn - 09-28-2018, 05:23 PM
RE: Philco 66B restoration - by klondike98 - 09-29-2018, 10:06 PM
RE: Philco 66B restoration - by OldRestorer - 10-02-2018, 08:59 AM
RE: Philco 66B restoration - by klondike98 - 10-06-2018, 04:30 PM
RE: Philco 66B restoration - by klondike98 - 10-10-2018, 09:06 PM
RE: Philco 66B restoration - by klondike98 - 10-14-2018, 07:08 PM
RE: Philco 66B restoration - by Steve Davis - 10-14-2018, 08:46 PM
RE: Philco 66B restoration - by klondike98 - 10-14-2018, 11:24 PM
RE: Philco 66B restoration - by klondike98 - 10-20-2018, 07:16 PM
RE: Philco 66B restoration - by klondike98 - 10-26-2018, 03:14 PM
RE: Philco 66B restoration - by Ron Ramirez - 10-26-2018, 03:26 PM
RE: Philco 66B restoration - by klondike98 - 10-26-2018, 04:07 PM
RE: Philco 66B restoration - by Radioroslyn - 10-26-2018, 04:51 PM
RE: Philco 66B restoration - by Ron Ramirez - 10-26-2018, 07:30 PM
RE: Philco 66B restoration - by klondike98 - 11-01-2018, 07:38 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 1438 online users. [Complete List]
» 1 Member(s) | 1437 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration