1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 89L-troubles
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#23

10-17-2018, 05:51 PM
So whatdoyougot on pin 5 of the 42? Should be at ground (0v) and pin 4? Should be abt -20vdc. Oh and pin 3 abt the same as pin 2. Is heater in the 42 working?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 10-17-2018, 05:53 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 89L-troubles - by vecher - 04-30-2018, 08:41 PM
RE: Philco 89L - by KCMike - 04-30-2018, 09:02 PM
RE: Philco 89L - by Chas - 05-02-2018, 08:27 PM
RE: Philco 89L - by vecher - 06-24-2018, 11:07 AM
RE: Philco 89L - by Radioroslyn - 06-24-2018, 11:49 AM
RE: Philco 89L - by vecher - 06-24-2018, 02:01 PM
RE: Philco 89L - by Radioroslyn - 06-24-2018, 02:57 PM
RE: Philco 89L - by vecher - 06-24-2018, 04:17 PM
RE: Philco 89L - by vecher - 08-03-2018, 11:28 PM
RE: Philco 89L - by Chas - 08-04-2018, 10:44 AM
RE: Philco 89L - by radio63 - 08-14-2018, 08:12 PM
RE: Philco 89L - by Chas - 08-14-2018, 09:39 PM
RE: Philco 89L - by radio63 - 08-15-2018, 03:23 PM
RE: Philco 89L - by jcassity - 08-18-2018, 10:55 AM
RE: Philco 89L - by vecher - 09-09-2018, 12:22 AM
RE: Philco 89L - by Radioroslyn - 09-09-2018, 01:00 AM
RE: Philco 89L - by vecher - 09-09-2018, 04:30 PM
RE: Philco 89L - by Radioroslyn - 09-09-2018, 06:28 PM
RE: Philco 89L - by vecher - 09-09-2018, 11:43 PM
RE: Philco 89L - by morzh - 09-10-2018, 08:37 AM
RE: Philco 89L-Problems - by vecher - 10-17-2018, 05:04 PM
RE: Philco 89L-troubles - by KCMike - 10-17-2018, 05:13 PM
RE: Philco 89L-troubles - by Radioroslyn - 10-17-2018, 05:51 PM
RE: Philco 89L-troubles - by Steve Davis - 10-17-2018, 06:53 PM
RE: Philco 89L-troubles - by vecher - 10-17-2018, 09:09 PM
RE: Philco 89L-troubles - by vecher - 10-17-2018, 10:49 PM
RE: Philco 89L-troubles - by Radioroslyn - 10-17-2018, 11:08 PM
RE: Philco 89L-troubles - by vecher - 10-18-2018, 12:01 PM
RE: Philco 89L-troubles - by vecher - 10-18-2018, 03:16 PM
RE: Philco 89L-troubles - by vecher - 10-18-2018, 08:24 PM
RE: Philco 89L-troubles - by vecher - 10-18-2018, 11:09 PM
RE: Philco 89L-troubles - by Arran - 10-19-2018, 03:12 AM
RE: Philco 89L-troubles - by vecher - 10-19-2018, 01:08 PM
RE: Philco 89L-troubles - by klondike98 - 10-19-2018, 01:13 PM
RE: Philco 89L-troubles - by vecher - 10-19-2018, 02:07 PM
RE: Philco 89L-troubles - by vecher - 10-21-2018, 11:35 PM
RE: Philco 89L-troubles - by vecher - 10-22-2018, 09:17 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration