Philco 66S Dial problem

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 66S Dial problem

PhilcoPhan1936
Jeff W.

Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR

10-20-2018, 10:05 AM

Ron,
Thanks for the info.
It was factory cut.
The holes to mount the escutcheon that was on there were the only ones.

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 66S Dial problem - by PhilcoPhan1936 - 10-19-2018, 09:22 PM

RE: Philco 66S Dial problem - by morzh - 10-19-2018, 09:56 PM

RE: Philco 66S Dial problem - by Ron Ramirez - 10-20-2018, 08:47 AM

RE: Philco 66S Dial problem - by PhilcoPhan1936 - 10-20-2018, 10:05 AM

RE: Philco 66S Dial problem - by Ron Ramirez - 10-20-2018, 10:29 AM

RE: Philco 66S Dial problem - by PhilcoPhan1936 - 10-20-2018, 04:32 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

Who's Online

There are currently 4709 online users. [Complete List]
» 2 Member(s) | 4707 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me