1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 66B restoration
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#33

10-26-2018, 07:30 PM
> It would seem much simpler just feed it from b+ that is over by the output stage.

I tried that once some years ago in a 66, and the set hummed until I redid it correctly with a choke, following the factory schematic. As I recall the original choke was bad but I found one in a junk Philco, either another 66 or possibly a 45, and it took care of the hum.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 66B restoration - by klondike98 - 09-24-2018, 07:08 PM
RE: Philco 66B restoration - by morzh - 09-24-2018, 07:15 PM
RE: Philco 66B restoration - by klondike98 - 09-24-2018, 07:24 PM
RE: Philco 66B restoration - by Arran - 09-25-2018, 04:18 AM
RE: Philco 66B restoration - by morzh - 09-25-2018, 07:51 AM
RE: Philco 66B restoration - by klondike98 - 09-25-2018, 05:49 PM
RE: Philco 66B restoration - by morzh - 09-25-2018, 07:15 PM
RE: Philco 66B restoration - by klondike98 - 09-26-2018, 09:17 AM
RE: Philco 66B restoration - by morzh - 09-26-2018, 11:47 AM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 12:21 PM
RE: Philco 66B restoration - by morzh - 09-27-2018, 03:22 PM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 07:46 PM
RE: Philco 66B restoration - by Ron Ramirez - 09-27-2018, 07:59 PM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 08:09 PM
RE: Philco 66B restoration - by morzh - 09-27-2018, 10:08 PM
RE: Philco 66B restoration - by klondike98 - 09-27-2018, 10:42 PM
RE: Philco 66B restoration - by klondike98 - 09-28-2018, 02:30 PM
RE: Philco 66B restoration - by morzh - 09-28-2018, 02:38 PM
RE: Philco 66B restoration - by Radioroslyn - 09-28-2018, 05:23 PM
RE: Philco 66B restoration - by klondike98 - 09-29-2018, 10:06 PM
RE: Philco 66B restoration - by OldRestorer - 10-02-2018, 08:59 AM
RE: Philco 66B restoration - by klondike98 - 10-06-2018, 04:30 PM
RE: Philco 66B restoration - by klondike98 - 10-10-2018, 09:06 PM
RE: Philco 66B restoration - by klondike98 - 10-14-2018, 07:08 PM
RE: Philco 66B restoration - by Steve Davis - 10-14-2018, 08:46 PM
RE: Philco 66B restoration - by klondike98 - 10-14-2018, 11:24 PM
RE: Philco 66B restoration - by klondike98 - 10-20-2018, 07:16 PM
RE: Philco 66B restoration - by klondike98 - 10-26-2018, 03:14 PM
RE: Philco 66B restoration - by Ron Ramirez - 10-26-2018, 03:26 PM
RE: Philco 66B restoration - by klondike98 - 10-26-2018, 04:07 PM
RE: Philco 66B restoration - by Radioroslyn - 10-26-2018, 04:51 PM
RE: Philco 66B restoration - by Ron Ramirez - 10-26-2018, 07:30 PM
RE: Philco 66B restoration - by klondike98 - 11-01-2018, 07:38 PM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 3619 online users. [Complete List]
» 1 Member(s) | 3618 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration