1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
PHILCO 116B labels
don'tdomelikethat
Unregistered
 
#3

09-27-2010, 09:16 AM
I'd really appreciate that scan, Ron. Thanks! I'm on vacation this week, and the main item on my "to do" list is getting my 116 back together. Yesterday, it was in the 70's with about 35% humidity here in northern WV, so I grabbed the nice weather opportunity to spray the Mohawk toner and lacquer (refer to my post about needing advice on this). It turned out well, and the cabinet has it's original look to it again. Today, I'm cleaning, and lubing the dial drive as per the article on rebuilding dial drives for the 116, 640, 650, etc. I still have to do an alignment, and then get it all back together, hopefully...keeping fingers crossed! Your scan would be a nice finishing touch! Thanks!
« Next Oldest | Next Newest »


Messages In This Thread
PHILCO 116B labels - by don'tdomelikethat - 09-26-2010, 02:07 PM
Re: PHILCO 116B labels - by Ron Ramirez - 09-26-2010, 08:27 PM
Re: PHILCO 116B labels - by don'tdomelikethat - 09-27-2010, 09:16 AM
Re: PHILCO 116B labels - by Ron Ramirez - 09-27-2010, 09:59 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 6967 online users. [Complete List]
» 3 Member(s) | 6964 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration