1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Trying To ID Philco Speaker
Pepperoni
Member
***
Posts: 160
Threads: 42
Joined: Apr 2011
City: New Port Richey State, Province, Country: Florida
#5

11-14-2018, 09:42 AM
I removed the wire cover from the output transformer for the purpose of taking a pic of the transformer. Here's the best specs I can find for the 37-630 model speaker and it's labeled as a -630X. Note the specs on the transformer and field coil highlighted in red. The output transformer on this speaker reads 168 ohms as stated earlier. 

Can I use the speaker in question on my 37-630?

H-24
10-1/2"
36-1224
37-630X
1-6F6G as Pentode
2580
7,100 Ω
1.25 Ω
02625
450 Ω - Output Transformer Primary
36-3665

1140 Ω - Field Coil Resistance

Pepperoni
"It's Nice To Be Nice To The Nice"
Major Frank Burns Mash 4077th
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Trying To ID Philco Speaker - by Pepperoni - 11-13-2018, 02:24 PM
RE: Trying To ID Philco Speaker - by morzh - 11-13-2018, 03:29 PM
RE: Trying To ID Philco Speaker - by Pepperoni - 11-13-2018, 05:20 PM
RE: Trying To ID Philco Speaker - by StephenB - 11-13-2018, 07:02 PM
RE: Trying To ID Philco Speaker - by Pepperoni - 11-14-2018, 09:42 AM
RE: Trying To ID Philco Speaker - by Radioroslyn - 11-14-2018, 10:35 AM
RE: Trying To ID Philco Speaker - by Pepperoni - 11-14-2018, 11:36 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration