Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Highboy 96 Chassis
#11

A bonus for the Mac was you could purchase it for $0.65-$0.75 on the dollar haha
After I posted about the dashboard I looked on eeevilPay and there is one the same color sitting at about $50 Beaver Skins in great condition so obviously this is a good indicator. Peanut tubes means early 50's and up compared to all of my 40's and older sets with good ol wooden cabinets with the exception of my Philco "black toe" or my Sieg Heil Bakelite "Fanger".
As for the 96 other than functioning very well, complete except for the metal shield covering the back of the chassis, and the speaker still covered in cloth at the back I guess it is a good source of 1930 type toobs, Philco transformers (and my my my there are enough of them on this beast) and most likely is infested with block capacitors as well. Yes the value of the low and highboys is surprisingly low for what these sets are compared to the 2 and 3 dialers needing horns and batteries. At least these are "modern" in comparison.


Messages In This Thread
Philco Highboy 96 Chassis - by Philco444 - 11-14-2018, 08:58 PM
RE: Philco Highboy 96 Chassis - by morzh - 11-14-2018, 09:08 PM
RE: Philco Highboy 96 Chassis - by Philco444 - 11-14-2018, 10:20 PM
RE: Philco Highboy 96 Chassis - by klondike98 - 11-14-2018, 10:23 PM
RE: Philco Highboy 96 Chassis - by morzh - 11-14-2018, 10:31 PM
RE: Philco Highboy 96 Chassis - by Philco444 - 11-14-2018, 11:28 PM
RE: Philco Highboy 96 Chassis - by morzh - 11-14-2018, 11:48 PM
RE: Philco Highboy 96 Chassis - by Philco444 - 11-16-2018, 01:39 AM
RE: Philco Highboy 96 Chassis - by Arran - 11-16-2018, 04:46 AM
RE: Philco Highboy 96 Chassis - by morzh - 11-16-2018, 09:28 AM
RE: Philco Highboy 96 Chassis - by Philco444 - 11-16-2018, 05:40 PM
RE: Philco Highboy 96 Chassis - by Philco444 - 11-20-2018, 05:11 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5197 online users. [Complete List]
» 2 Member(s) | 5195 Guest(s)
AvatarAvatar

>