1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 2 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 116B chassis restoration
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#31

12-03-2018, 09:56 PM
A little progress today.  Stuffed the two caps discussed above and the #100 electrolytic.  This was the first time I've opened up one of these older can caps and it still was full of liquid!  The 10uF Solen film cap just fit into the pvc coupling that helps hold the two pieces of the can together.  Had to make a little groove in the pvc to allow the lead that will go to the transformer CT fit along the side of the can.  

[Image: https://www.dropbox.com/s/8z5g9cnpgq8jwx....jpg?raw=1]
[Image: https://www.dropbox.com/s/jocurwluks0hc4....jpg?raw=1]
[Image: https://www.dropbox.com/s/ovaxna3l3so701....jpg?raw=1]
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 116B chassis restoration - by klondike98 - 11-05-2018, 08:05 PM
RE: Philco 116B chassis restoration - by amptramp - 11-05-2018, 08:41 PM
RE: Philco 116B chassis restoration - by Arran - 11-07-2018, 04:32 AM
RE: Philco 116B chassis restoration - by morzh - 11-15-2018, 03:44 PM
RE: Philco 116B chassis restoration - by KCMike - 11-20-2018, 07:39 PM
RE: Philco 116B chassis restoration - by klondike98 - 12-03-2018, 09:56 PM
RE: Philco 116B chassis restoration - by KCMike - 12-03-2018, 10:03 PM
RE: Philco 116B chassis restoration - by Arran - 12-30-2018, 04:53 PM
RE: Philco 116B chassis restoration - by KCMike - 01-20-2019, 06:09 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration