Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith TO H500
#5

Arran,

Yes every single Bumblebee encountered in Stromberg, in Zenith or in my Eico amps are bad and bad in a worse way than paper shell ones. Almost 3 times the value. So there is no question in my mind as to whether replace them or not. Not that there ever was a question about any paper cap.

The resistor is indeed the one that is sand coated.
For now I will leave it be as else I wll have to buy one or even two (f I want to honor that voltage adjustment switch). But then I rn these radios from batteries so neither selenium element or the resistor are going to be used much.

More is coming today.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Zenith TO H500 - by morzh - 12-15-2018, 11:28 PM
RE: Zenith TO H500 - by sam - 12-16-2018, 06:46 PM
RE: Zenith TO H500 - by morzh - 12-16-2018, 08:26 PM
RE: Zenith TO H500 - by Arran - 12-17-2018, 05:02 AM
RE: Zenith TO H500 - by morzh - 12-17-2018, 10:34 AM
RE: Zenith TO H500 - by morzh - 12-17-2018, 01:05 PM
RE: Zenith TO H500 - by jcassity - 12-17-2018, 01:29 PM
RE: Zenith TO H500 - by morzh - 12-17-2018, 04:32 PM
RE: Zenith TO H500 - by EdHolland - 12-17-2018, 05:01 PM
RE: Zenith TO H500 - by morzh - 12-17-2018, 09:29 PM
RE: Zenith TO H500 - by EdHolland - 12-17-2018, 09:33 PM
RE: Zenith TO H500 - by morzh - 12-17-2018, 09:54 PM
RE: Zenith TO H500 - by morzh - 12-18-2018, 05:18 PM
RE: Zenith TO H500 - by sam - 12-18-2018, 05:46 PM
RE: Zenith TO H500 - by morzh - 12-18-2018, 06:16 PM
RE: Zenith TO H500 - by morzh - 01-06-2019, 11:11 PM
RE: Zenith TO H500 - by Arran - 01-07-2019, 01:41 AM
RE: Zenith TO H500 - by morzh - 01-07-2019, 11:30 AM
RE: Zenith TO H500 - by morzh - 01-12-2019, 11:20 PM
RE: Zenith TO H500 - by morzh - 01-13-2019, 07:27 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum! :wave: Here's the schematic for that radio from our digital library: Something to do bef...klondike98 — 08:05 PM

[-]
Who's Online
There are currently no members online.

>