1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Late model 116B cabinet
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#7

12-17-2018, 04:25 PM
So now that I have all of the eeg glue out of my hair it's back to the cabinet at hand. Got it all back together with trim and molding in place. Grain filled and sand sealer. Repaired the hole in the side and toned. Both of us need a little break to out gas a bit. It's looking pretty good but it has been breaking out in a white rash here and there after applying sanding sealer. Have it under control but it's a little annoying. Think I'm going to set it aside till after the holidays. I can't find my last PHILCO logo decals so sent for a new sheet. 

Here's quick peek so far.


Attached Files Image(s)
   
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 01-07-2019, 11:10 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Late model 116B cabinet - by Radioroslyn - 12-04-2018, 01:16 PM
RE: Late model 116B cabinet - by OldRestorer - 12-04-2018, 02:26 PM
RE: Late model 116B cabinet - by Ron Ramirez - 12-04-2018, 02:51 PM
RE: Late model 116B cabinet - by Radioroslyn - 12-07-2018, 10:17 PM
RE: Late model 116B cabinet - by klondike98 - 12-07-2018, 10:53 PM
RE: Late model 116B cabinet - by Arran - 12-14-2018, 12:42 AM
RE: Late model 116B cabinet - by Radioroslyn - 12-17-2018, 04:25 PM
RE: Late model 116B cabinet - by Ron Ramirez - 12-17-2018, 04:32 PM
RE: Late model 116B cabinet - by Radioroslyn - 12-17-2018, 07:37 PM
RE: Late model 116B cabinet - by Ron Ramirez - 12-17-2018, 07:50 PM
RE: Late model 116B cabinet - by Arran - 12-19-2018, 05:29 AM
RE: Late model 116B cabinet - by Radioroslyn - 12-19-2018, 11:42 AM
RE: Late model 116B cabinet - by Ron Ramirez - 12-19-2018, 11:44 AM
RE: Late model 116B cabinet - by Arran - 12-20-2018, 06:30 AM
RE: Late model 116B cabinet - by OldRestorer - 12-20-2018, 07:54 AM
RE: Late model 116B cabinet - by Radioroslyn - 12-20-2018, 12:22 PM
RE: Late model 116B cabinet - by jcassity - 12-21-2018, 11:36 AM
RE: Late model 116B cabinet - by OldRestorer - 12-21-2018, 12:08 PM
RE: Late model 116B cabinet - by Ron Ramirez - 12-21-2018, 12:48 PM
RE: Late model 116B cabinet - by Radioroslyn - 12-21-2018, 05:17 PM
RE: Late model 116B cabinet - by OldRestorer - 12-23-2018, 08:06 AM
RE: Late model 116B cabinet - by Radioroslyn - 01-23-2019, 08:57 PM
RE: Late model 116B cabinet - by KCMike - 01-23-2019, 09:58 PM
RE: Late model 116B cabinet - by madsowry - 01-23-2019, 11:39 PM
RE: Late model 116B cabinet - by klondike98 - 01-24-2019, 08:35 AM
RE: Late model 116B cabinet - by Ron Ramirez - 01-24-2019, 08:54 AM
RE: Late model 116B cabinet - by Radioroslyn - 01-24-2019, 11:31 AM
RE: Late model 116B cabinet - by Ron Ramirez - 01-24-2019, 11:49 AM
RE: Late model 116B cabinet - by Phlogiston - 01-24-2019, 12:12 PM
RE: Late model 116B cabinet - by Radioroslyn - 01-24-2019, 02:20 PM
RE: Late model 116B cabinet - by jcassity - 02-01-2019, 06:37 PM
RE: Late model 116B cabinet - by Radioroslyn - 02-01-2019, 06:42 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration