Zenith TO H500

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith TO H500

Arran
Phorum Expert

Posts: 4,686
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

#17

01-07-2019, 12:41 AM

Mike;
I would go with something between 47 and 80 Ohms resistance, with 80 at the high end, I'm not sure about the 1LN6 but the 1R5s are very fussy about how much voltage they receive, sometimes they will stop oscillating if the voltage is cut down too much, especially on the filament side.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith TO H500 - by morzh - 12-15-2018, 10:28 PM

RE: Zenith TO H500 - by sam - 12-16-2018, 05:46 PM

RE: Zenith TO H500 - by morzh - 12-16-2018, 07:26 PM

RE: Zenith TO H500 - by Arran - 12-17-2018, 04:02 AM

RE: Zenith TO H500 - by morzh - 12-17-2018, 09:34 AM

RE: Zenith TO H500 - by morzh - 12-17-2018, 12:05 PM

RE: Zenith TO H500 - by jcassity - 12-17-2018, 12:29 PM

RE: Zenith TO H500 - by morzh - 12-17-2018, 03:32 PM

RE: Zenith TO H500 - by EdHolland - 12-17-2018, 04:01 PM

RE: Zenith TO H500 - by morzh - 12-17-2018, 08:29 PM

RE: Zenith TO H500 - by EdHolland - 12-17-2018, 08:33 PM

RE: Zenith TO H500 - by morzh - 12-17-2018, 08:54 PM

RE: Zenith TO H500 - by morzh - 12-18-2018, 04:18 PM

RE: Zenith TO H500 - by sam - 12-18-2018, 04:46 PM

RE: Zenith TO H500 - by morzh - 12-18-2018, 05:16 PM

RE: Zenith TO H500 - by morzh - 01-06-2019, 10:11 PM

RE: Zenith TO H500 - by Arran - 01-07-2019, 12:41 AM

RE: Zenith TO H500 - by morzh - 01-07-2019, 10:30 AM

RE: Zenith TO H500 - by morzh - 01-12-2019, 10:20 PM

RE: Zenith TO H500 - by morzh - 01-13-2019, 06:27 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

Who's Online

There are currently 2414 online users. [Complete List]
» 1 Member(s) | 2413 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me