1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Nathan's 38-116XX Restoration
rfeenstra
Phorum Expert
*****
Posts: 1,190
Threads: 50
Joined: Oct 2017
City: Allendale, MI
#30

01-19-2019, 01:46 PM
Well, you inspired me to start my 37-116!  Decided to start the sub-chassis first and have that finished.  Had to disassemble to get to all the caps and check the resistors.  I'll start another thread to note the progress.
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: Nathan's 38-116XX Restoration - by klondike98 - 01-04-2019, 12:04 AM
RE: Nathan's 38-116XX Restoration - by rfeenstra - 01-04-2019, 12:12 AM
RE: Nathan's 38-116XX Restoration - by sam - 01-05-2019, 09:15 PM
RE: Nathan's 38-116XX Restoration - by klondike98 - 01-05-2019, 11:29 PM
RE: Nathan's 38-116XX Restoration - by 462ron - 01-07-2019, 09:06 AM
RE: Nathan's 38-116XX Restoration - by Jeremy S - 01-07-2019, 04:46 PM
RE: Nathan's 38-116XX Restoration - by rfeenstra - 01-08-2019, 12:04 AM
RE: Nathan's 38-116XX Restoration - by rfeenstra - 01-10-2019, 12:42 AM
RE: Nathan's 38-116XX Restoration - by amptramp - 01-10-2019, 10:21 PM
RE: Nathan's 38-116XX Restoration - by sam - 01-11-2019, 12:23 PM
RE: Nathan's 38-116XX Restoration - by tbone - 01-12-2019, 07:48 AM
RE: Nathan's 38-116XX Restoration - by klondike98 - 01-18-2019, 10:19 AM
RE: Nathan's 38-116XX Restoration - by EdHolland - 01-18-2019, 02:41 PM
RE: Nathan's 38-116XX Restoration - by rfeenstra - 01-19-2019, 01:46 PM
RE: Nathan's 38-116XX Restoration - by rfeenstra - 02-17-2019, 04:25 PM
RE: Nathan's 38-116XX Restoration - by rfeenstra - 02-17-2019, 05:15 PM
RE: Nathan's 38-116XX Restoration - by klondike98 - 02-17-2019, 05:33 PM
RE: Nathan's 38-116XX Restoration - by morzh - 02-17-2019, 05:38 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 6288 online users. [Complete List]
» 1 Member(s) | 6287 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration