Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Heathkit GD-1B
#21

Ok, Fixed.. I went over it checking every connection and every wire.. I missed a connection..After putting wire where it was supposed to go I now have Grid current.. The OSC still works and is very Stable on counter.. Next to check to see if I can measure a circuit.. Have to make up a Resonant circuit..

So so far so good..

Skip


Messages In This Thread
Heathkit GD-1B - by vecher - 12-31-2018, 06:37 PM
RE: Heathkit GD-1B - by gregb - 12-31-2018, 06:44 PM
RE: Heathkit GD-1B - by Radioroslyn - 12-31-2018, 06:58 PM
RE: Heathkit GD-1B - by vecher - 12-31-2018, 06:59 PM
RE: Heathkit GD-1B - by vecher - 12-31-2018, 07:02 PM
RE: Heathkit GD-1B - by Steve Davis - 12-31-2018, 07:56 PM
RE: Heathkit GD-1B - by Steve Davis - 12-31-2018, 07:57 PM
RE: Heathkit GD-1B - by Radioroslyn - 12-31-2018, 08:03 PM
RE: Heathkit GD-1B - by vecher - 01-01-2019, 10:09 PM
RE: Heathkit GD-1B - by Chas - 01-01-2019, 11:17 PM
RE: Heathkit GD-1B - by vecher - 01-02-2019, 12:11 AM
RE: Heathkit GD-1B - by Radioroslyn - 01-03-2019, 11:28 AM
RE: Heathkit GD-1B - by vecher - 01-09-2019, 01:46 AM
RE: Heathkit GD-1B - by Surfur - 01-17-2019, 01:46 AM
RE: Heathkit GD-1B - by Radioroslyn - 01-17-2019, 10:52 AM
RE: Heathkit GD-1B - by Surfur - 01-17-2019, 01:24 PM
RE: Heathkit GD-1B - by vecher - 01-19-2019, 12:14 AM
RE: Heathkit GD-1B - by vecher - 01-19-2019, 09:39 PM
RE: Heathkit GD-1B - by Surfur - 01-20-2019, 02:58 AM
RE: Heathkit GD-1B - by vecher - 01-20-2019, 11:10 AM
RE: Heathkit GD-1B - by vecher - 01-20-2019, 04:56 PM
RE: Heathkit GD-1B - by KCMike - 01-20-2019, 05:53 PM
RE: Heathkit GD-1B - by vecher - 01-20-2019, 08:29 PM
RE: Heathkit GD-1B - by vecher - 01-21-2019, 12:04 AM
RE: Heathkit GD-1B - by vecher - 02-15-2019, 09:17 PM
RE: Heathkit GD-1B - by EdHolland - 02-15-2019, 09:39 PM
RE: Heathkit GD-1B - by Surfur - 03-12-2019, 10:12 PM
RE: Heathkit GD-1B - by EdHolland - 03-12-2019, 11:57 PM
RE: Heathkit GD-1B - by vecher - 03-13-2019, 03:00 PM



Users browsing this thread: 10 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM

[-]
Who's Online
There are currently 7982 online users. [Complete List]
» 1 Member(s) | 7981 Guest(s)
Avatar

>