1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
40-140 Audio detector question
amptramp
Junior Member
**
Posts: 27
Threads: 1
Joined: Aug 2018
City: Mississauga State, Province, Country: Ontario
#9

01-22-2019, 08:35 PM
Nostalgiaair shows a different schematic.  I assume this one uses the capacitance between the parallel plates of the dual diode to couple IF into the second plate.  The schematic from the link above has the disadvantage of still back-biasing the detector.  I was using this:

http://www.nostalgiaair.org/pagesbymodel...013329.pdf

What circuit do you actually have?
Find
« Next Oldest | Next Newest »


Messages In This Thread
40-140 Audio detector question - by OZ4 - 01-20-2019, 04:47 AM
RE: 40-140 Audio detector question - by radiodale - 01-20-2019, 05:49 PM
RE: 40-140 Audio detector question - by OZ4 - 01-20-2019, 06:19 PM
RE: 40-140 Audio detector question - by OZ4 - 01-20-2019, 09:57 PM
RE: 40-140 Audio detector question - by OZ4 - 01-20-2019, 11:58 PM
RE: 40-140 Audio detector question - by OZ4 - 01-21-2019, 06:10 PM
RE: 40-140 Audio detector question - by amptramp - 01-22-2019, 12:46 AM
RE: 40-140 Audio detector question - by OZ4 - 01-22-2019, 12:47 PM
RE: 40-140 Audio detector question - by amptramp - 01-22-2019, 08:35 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7818 online users. [Complete List]
» 3 Member(s) | 7815 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration