1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Confirmation of a no-brainer, Please!
Robbie Roberts
Member
***
Posts: 147
Threads: 28
Joined: Nov 2005
#3

02-12-2006, 05:32 AM
Ok- Here's where I'm leaving it tonightIcon_sadTime for bed- 4 am) I have gotten things roughly adjusted. As I have no real clue what I'm doing, I'm following the directions best I can... While I have no appreciable understanding of a lot of this, I have it to the point is makes squakies and squeals at approximately the right positions that one might assume I am hitting stations, but have not quite gotten things reeled in.

I almost heard something that sounded like voice, but it may have been my imagination.(Does anyone know anything about a "Vogon Constructor Fleet and some Hyperspace Bypass? Seems we have fifteen minutes to vacate... But I may have misheard what I think I thought I might have heard...)

Anyway, frustrated for the night, I have also discovered this thing can squeal LOUD! Apparently that little 10000x multiplication of the resistance was just enough to quiet it. My faux resistor seems to be doing an adequate job- until a proper resistor makes an appearance. Now to just get all the adjusty thingys adjusted, and I might have a half decent receiver here!

Wouldn't that be nice! My 37-650 a going concern once again. Well, I can dream, can't I?

Still looking for answers/replies/suggestions regarding my earlier questions in this string...
Thanks!
Scott
Old Cars, Old Radios, Old Pipes and Young Women... What more is there?
Find
« Next Oldest | Next Newest »


Messages In This Thread
[No subject] - by Robbie Roberts - 02-12-2006, 03:00 AM
[No subject] - by Robbie Roberts - 02-12-2006, 05:32 AM
[No subject] - by Chuck Schwark - 02-12-2006, 11:53 AM
[No subject] - by Bill Hutchinson - 02-12-2006, 12:11 PM
[No subject] - by Robbie Roberts - 02-12-2006, 12:21 PM
[No subject] - by Robbie Roberts - 02-12-2006, 12:21 PM
[No subject] - by Chuck Schwark - 02-12-2006, 02:22 PM
[No subject] - by Robbie Roberts - 02-12-2006, 04:29 PM
[No subject] - by Robbie Roberts - 02-12-2006, 06:06 PM
[No subject] - by Robbie Roberts - 02-13-2006, 02:20 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration