Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-610 Restoration
#16

The first cap is 12uF.
The maximum the tube can tolerate is 20uF.
But you should not go much above 12uF as the voltage will rise and the rest of the tubes will run hotter than needed.

Pick the closest value; 12uF does exist in 500V rating. Or you could parallel or serialize. 10uF by Panasonic I use is a better cap with better ripple rating.

The second cap could be almost anything; 10uF is fine, 20uF is also fine. So is 30.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
37-610 Restoration - by Randy Ulrich - 01-17-2019, 10:43 AM
RE: 37-610 Restoration - by Randy Ulrich - 01-17-2019, 12:18 PM
RE: 37-610 Restoration - by sam - 01-17-2019, 02:19 PM
RE: 37-610 Restoration - by Radioroslyn - 01-17-2019, 04:00 PM
RE: 37-610 Restoration - by mikethedruid - 01-17-2019, 06:51 PM
RE: 37-610 Restoration - by Ron Ramirez - 01-17-2019, 08:57 PM
RE: 37-610 Restoration - by KCMike - 01-17-2019, 10:28 PM
RE: 37-610 Restoration - by Ron Ramirez - 01-17-2019, 10:32 PM
RE: 37-610 Restoration - by Randy Ulrich - 01-18-2019, 07:10 AM
RE: 37-610 Restoration - by Ron Ramirez - 01-18-2019, 07:17 AM
RE: 37-610 Restoration - by Randy Ulrich - 01-18-2019, 07:27 AM
RE: 37-610 Restoration - by Ron Ramirez - 01-18-2019, 07:31 AM
RE: 37-610 Restoration - by Randy Ulrich - 01-18-2019, 10:00 AM
RE: 37-610 Restoration - by Ron Ramirez - 01-18-2019, 10:26 AM
RE: 37-610 Restoration - by Randy Ulrich - 01-29-2019, 05:59 PM
RE: 37-610 Restoration - by morzh - 01-29-2019, 06:22 PM
RE: 37-610 Restoration - by klondike98 - 01-29-2019, 06:36 PM
RE: 37-610 Restoration - by Randy Ulrich - 02-01-2019, 12:52 PM
RE: 37-610 Restoration - by Ron Ramirez - 02-01-2019, 01:09 PM
RE: 37-610 Restoration - by Randy Ulrich - 02-01-2019, 04:19 PM
RE: 37-610 Restoration - by klondike98 - 02-01-2019, 06:47 PM
RE: 37-610 Restoration - by Randy Ulrich - 02-01-2019, 08:16 PM
RE: 37-610 Restoration - by Randy Ulrich - 02-23-2019, 05:40 AM
RE: 37-610 Restoration - by KCMike - 02-23-2019, 07:48 PM
RE: 37-610 Restoration - by Randy Ulrich - 02-25-2019, 11:56 AM
RE: 37-610 Restoration - by morzh - 02-25-2019, 01:08 PM



Users browsing this thread: 11 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>