1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
GE 200 Reception issue
Paul Philco322
Super Moderator
******
Posts: 4,433
Threads: 419
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#14

02-12-2019, 09:16 PM
This is the only set in my limited time in this hobby I have seen with this plate.

Paul
Tubetalk1
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
GE 200 Reception issue - by Paul Philco322 - 02-01-2019, 06:16 PM
RE: GE 200 Reception issue - by jcassity - 02-01-2019, 06:47 PM
RE: GE 200 Reception issue - by David - 02-01-2019, 06:55 PM
RE: GE 200 Reception issue - by tbone - 02-02-2019, 07:31 AM
RE: GE 200 Reception issue - by Arran - 02-02-2019, 05:59 PM
RE: GE 200 Reception issue - by Paul Philco322 - 02-02-2019, 08:28 PM
RE: GE 200 Reception issue - by Paul Philco322 - 02-04-2019, 10:33 PM
RE: GE 200 Reception issue - by Paul Philco322 - 02-11-2019, 08:56 PM
RE: GE 200 Reception issue - by David - 02-12-2019, 01:31 PM
RE: GE 200 Reception issue - by Eliot Ness - 02-12-2019, 05:07 PM
RE: GE 200 Reception issue - by David - 02-12-2019, 06:44 PM
RE: GE 200 Reception issue - by Paul Philco322 - 02-12-2019, 09:16 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)