Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE g-97
#7

I got the candohm problem sorted out, Speaker has a hum, But no response to dial or anything, I injected a signal on the blue wire (see diagram above) going to output transformer, and I can just make out the tone if I stick my ear into the speaker cone. If Im correct that is pointing towards a problem in my output transformer. which is strange since the resistance measurements where correct. Am I on the right track here?


Messages In This Thread
GE g-97 - by rperry - 02-09-2019, 12:18 PM
RE: GE g-97 - by mark123 - 02-11-2019, 02:11 PM
RE: GE g-97 - by rperry - 02-11-2019, 08:15 PM
RE: GE g-97 - by jcassity - 02-12-2019, 08:58 AM
RE: GE g-97 - by 35Z5 - 02-12-2019, 09:40 AM
RE: GE g-97 - by rperry - 02-12-2019, 11:04 AM
RE: GE g-97 - by rperry - 02-13-2019, 05:21 PM
RE: GE g-97 - by 35Z5 - 02-13-2019, 08:22 PM
RE: GE g-97 - by rperry - 02-14-2019, 09:37 AM
RE: GE g-97 - by 35Z5 - 02-14-2019, 11:41 AM
RE: GE g-97 - by rperry - 02-14-2019, 06:16 PM
RE: GE g-97 - by 35Z5 - 02-14-2019, 07:57 PM
RE: GE g-97 - by rperry - 02-14-2019, 08:04 PM
RE: GE g-97 - by 35Z5 - 02-15-2019, 10:02 AM
RE: GE g-97 - by rperry - 02-15-2019, 05:35 PM
RE: GE g-97 - by jcassity - 02-15-2019, 06:59 PM
RE: GE g-97 - by 35Z5 - 02-15-2019, 07:09 PM
RE: GE g-97 - by jcassity - 02-16-2019, 10:51 AM
RE: GE g-97 - by David - 02-16-2019, 11:15 AM
RE: GE g-97 - by rperry - 02-17-2019, 07:41 PM
RE: GE g-97 - by rperry - 02-19-2019, 01:07 PM
RE: GE g-97 - by Kenneth F. Besso Jr. - 02-19-2019, 06:46 PM
RE: GE g-97 - by rperry - 02-19-2019, 09:18 PM
RE: GE g-97 - by 35Z5 - 02-20-2019, 02:07 PM
RE: GE g-97 - by morzh - 02-20-2019, 02:43 PM
RE: GE g-97 - by rperry - 03-06-2019, 12:54 PM
RE: GE g-97 - by rperry - 03-08-2019, 06:31 PM
RE: GE g-97 - by Radioroslyn - 03-08-2019, 07:21 PM
RE: GE g-97 - by rperry - 03-15-2019, 11:39 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>