GE g-97

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

GE g-97

35Z5
Member

Posts: 184
Threads: 3
Joined: Feb 2018
City: Chesapeake VA

#14

02-15-2019, 11:02 AM

Ummm, how about injecting signal into pin 4 of 42? If that isn't passing signal problem definitely in output section.

Are you sure the output transformer primary(blue, 500 ohm) is connected to plate and not one of other windings?

Tom

Find

« Next Oldest | Next Newest »

Messages In This Thread

GE g-97 - by rperry - 02-09-2019, 01:18 PM

RE: GE g-97 - by mark123 - 02-11-2019, 03:11 PM

RE: GE g-97 - by rperry - 02-11-2019, 09:15 PM

RE: GE g-97 - by jcassity - 02-12-2019, 09:58 AM

RE: GE g-97 - by 35Z5 - 02-12-2019, 10:40 AM

RE: GE g-97 - by rperry - 02-12-2019, 12:04 PM

RE: GE g-97 - by rperry - 02-13-2019, 06:21 PM

RE: GE g-97 - by 35Z5 - 02-13-2019, 09:22 PM

RE: GE g-97 - by rperry - 02-14-2019, 10:37 AM

RE: GE g-97 - by 35Z5 - 02-14-2019, 12:41 PM

RE: GE g-97 - by rperry - 02-14-2019, 07:16 PM

RE: GE g-97 - by 35Z5 - 02-14-2019, 08:57 PM

RE: GE g-97 - by rperry - 02-14-2019, 09:04 PM

RE: GE g-97 - by 35Z5 - 02-15-2019, 11:02 AM

RE: GE g-97 - by rperry - 02-15-2019, 06:35 PM

RE: GE g-97 - by jcassity - 02-15-2019, 07:59 PM

RE: GE g-97 - by 35Z5 - 02-15-2019, 08:09 PM

RE: GE g-97 - by jcassity - 02-16-2019, 11:51 AM

RE: GE g-97 - by David - 02-16-2019, 12:15 PM

RE: GE g-97 - by rperry - 02-17-2019, 08:41 PM

RE: GE g-97 - by rperry - 02-19-2019, 02:07 PM

RE: GE g-97 - by Kenneth F. Besso Jr. - 02-19-2019, 07:46 PM

RE: GE g-97 - by rperry - 02-19-2019, 10:18 PM

RE: GE g-97 - by 35Z5 - 02-20-2019, 03:07 PM

RE: GE g-97 - by morzh - 02-20-2019, 03:43 PM

RE: GE g-97 - by rperry - 03-06-2019, 01:54 PM

RE: GE g-97 - by rperry - 03-08-2019, 07:31 PM

RE: GE g-97 - by Radioroslyn - 03-08-2019, 08:21 PM

RE: GE g-97 - by rperry - 03-15-2019, 12:39 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 5228 online users. [Complete List]
» 2 Member(s) | 5226 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me