GE g-97

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

GE g-97

rperry
Junior Member

Posts: 37
Threads: 5
Joined: Jan 2019
City: Ranger State, Province, Country: Ga

#15

02-15-2019, 05:35 PM

I started investigating the speaker and output transformer again and I made a few discoveries. On the connector where the "green" wire attaches the solder and wire are missing from the pin. (see Picture) also when I took my initial resistance readings I made an error. Where the schematic is showing 5 ohms across the speaker leads I have .9.. So it looks like I'm on the hunt for a new output transformer.

Ryan

Find

« Next Oldest | Next Newest »

Messages In This Thread

GE g-97 - by rperry - 02-09-2019, 12:18 PM

RE: GE g-97 - by mark123 - 02-11-2019, 02:11 PM

RE: GE g-97 - by rperry - 02-11-2019, 08:15 PM

RE: GE g-97 - by jcassity - 02-12-2019, 08:58 AM

RE: GE g-97 - by 35Z5 - 02-12-2019, 09:40 AM

RE: GE g-97 - by rperry - 02-12-2019, 11:04 AM

RE: GE g-97 - by rperry - 02-13-2019, 05:21 PM

RE: GE g-97 - by 35Z5 - 02-13-2019, 08:22 PM

RE: GE g-97 - by rperry - 02-14-2019, 09:37 AM

RE: GE g-97 - by 35Z5 - 02-14-2019, 11:41 AM

RE: GE g-97 - by rperry - 02-14-2019, 06:16 PM

RE: GE g-97 - by 35Z5 - 02-14-2019, 07:57 PM

RE: GE g-97 - by rperry - 02-14-2019, 08:04 PM

RE: GE g-97 - by 35Z5 - 02-15-2019, 10:02 AM

RE: GE g-97 - by rperry - 02-15-2019, 05:35 PM

RE: GE g-97 - by jcassity - 02-15-2019, 06:59 PM

RE: GE g-97 - by 35Z5 - 02-15-2019, 07:09 PM

RE: GE g-97 - by jcassity - 02-16-2019, 10:51 AM

RE: GE g-97 - by David - 02-16-2019, 11:15 AM

RE: GE g-97 - by rperry - 02-17-2019, 07:41 PM

RE: GE g-97 - by rperry - 02-19-2019, 01:07 PM

RE: GE g-97 - by Kenneth F. Besso Jr. - 02-19-2019, 06:46 PM

RE: GE g-97 - by rperry - 02-19-2019, 09:18 PM

RE: GE g-97 - by 35Z5 - 02-20-2019, 02:07 PM

RE: GE g-97 - by morzh - 02-20-2019, 02:43 PM

RE: GE g-97 - by rperry - 03-06-2019, 12:54 PM

RE: GE g-97 - by rperry - 03-08-2019, 06:31 PM

RE: GE g-97 - by Radioroslyn - 03-08-2019, 07:21 PM

RE: GE g-97 - by rperry - 03-15-2019, 11:39 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me