Simple Question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Simple Question

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

11-04-2010, 04:34 PM

When did Philco switch from cloth to rubber line cords?
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Simple Question - by 7estatdef - 11-04-2010, 04:34 PM

Re: Simple Question - by Ron Ramirez - 11-04-2010, 05:03 PM

Re: Simple Question - by 7estatdef - 11-07-2010, 10:22 PM

Re: Simple Question - by Ron Ramirez - 11-08-2010, 09:35 AM

Re: Simple Question - by codefox1 - 11-08-2010, 05:06 PM

Re: Simple Question - by Chuck Schwark - 11-08-2010, 08:16 PM

Re: Simple Question - by Ron Ramirez - 11-08-2010, 08:22 PM

Re: Simple Question - by Chuck Schwark - 11-08-2010, 08:24 PM

Re: Simple Question - by exray - 11-08-2010, 09:36 PM

Re: Simple Question - by codefox1 - 11-08-2010, 10:35 PM

Re: Simple Question - by 7estatdef - 11-09-2010, 07:10 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me