1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
GE g-97
Kenneth F. Besso Jr.
Senior Member
****
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
#22

02-19-2019, 07:46 PM
I had something like this happen,,,But ,,the transformer and speaker field. were wired WRONg in the plug ,,,Backwards,,,and still have a little tiny amount of sound,,,,till ,,I traces it all back to the tubes,,
Find
« Next Oldest | Next Newest »


Messages In This Thread
GE g-97 - by rperry - 02-09-2019, 01:18 PM
RE: GE g-97 - by mark123 - 02-11-2019, 03:11 PM
RE: GE g-97 - by rperry - 02-11-2019, 09:15 PM
RE: GE g-97 - by jcassity - 02-12-2019, 09:58 AM
RE: GE g-97 - by 35Z5 - 02-12-2019, 10:40 AM
RE: GE g-97 - by rperry - 02-12-2019, 12:04 PM
RE: GE g-97 - by rperry - 02-13-2019, 06:21 PM
RE: GE g-97 - by 35Z5 - 02-13-2019, 09:22 PM
RE: GE g-97 - by rperry - 02-14-2019, 10:37 AM
RE: GE g-97 - by 35Z5 - 02-14-2019, 12:41 PM
RE: GE g-97 - by rperry - 02-14-2019, 07:16 PM
RE: GE g-97 - by 35Z5 - 02-14-2019, 08:57 PM
RE: GE g-97 - by rperry - 02-14-2019, 09:04 PM
RE: GE g-97 - by 35Z5 - 02-15-2019, 11:02 AM
RE: GE g-97 - by rperry - 02-15-2019, 06:35 PM
RE: GE g-97 - by jcassity - 02-15-2019, 07:59 PM
RE: GE g-97 - by 35Z5 - 02-15-2019, 08:09 PM
RE: GE g-97 - by jcassity - 02-16-2019, 11:51 AM
RE: GE g-97 - by David - 02-16-2019, 12:15 PM
RE: GE g-97 - by rperry - 02-17-2019, 08:41 PM
RE: GE g-97 - by rperry - 02-19-2019, 02:07 PM
RE: GE g-97 - by Kenneth F. Besso Jr. - 02-19-2019, 07:46 PM
RE: GE g-97 - by rperry - 02-19-2019, 10:18 PM
RE: GE g-97 - by 35Z5 - 02-20-2019, 03:07 PM
RE: GE g-97 - by morzh - 02-20-2019, 03:43 PM
RE: GE g-97 - by rperry - 03-06-2019, 01:54 PM
RE: GE g-97 - by rperry - 03-08-2019, 07:31 PM
RE: GE g-97 - by Radioroslyn - 03-08-2019, 08:21 PM
RE: GE g-97 - by rperry - 03-15-2019, 12:39 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)