37-610 Restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

37-610 Restoration

Randy Ulrich
Junior Member

Posts: 13
Threads: 2
Joined: Jan 2019
City: Reinholds State, Province, Country: PA

#23

02-23-2019, 05:40 AM

Can you direct me to a good source for these caps? (The 8, 12 and 16 uf?) I've gone to Mouser, Digi-key and a few other suppliers but haven't really been too successful. You stated that Panasonic were the types you used but I've not found them.
Also are you using a 500V rating or is 450V sufficient? The original caps are missing on this radio so I don't know what the original ratings were and I'm not seeing a rating on the parts list.
And lastly, are you using radial or axial lead types?
Thanks in advance for helping out this newbie. Icon_smile

Find

« Next Oldest | Next Newest »

Messages In This Thread

37-610 Restoration - by Randy Ulrich - 01-17-2019, 10:43 AM

RE: 37-610 Restoration - by Randy Ulrich - 01-17-2019, 12:18 PM

RE: 37-610 Restoration - by sam - 01-17-2019, 02:19 PM

RE: 37-610 Restoration - by Radioroslyn - 01-17-2019, 04:00 PM

RE: 37-610 Restoration - by mikethedruid - 01-17-2019, 06:51 PM

RE: 37-610 Restoration - by Ron Ramirez - 01-17-2019, 08:57 PM

RE: 37-610 Restoration - by KCMike - 01-17-2019, 10:28 PM

RE: 37-610 Restoration - by Ron Ramirez - 01-17-2019, 10:32 PM

RE: 37-610 Restoration - by Randy Ulrich - 01-18-2019, 07:10 AM

RE: 37-610 Restoration - by Ron Ramirez - 01-18-2019, 07:17 AM

RE: 37-610 Restoration - by Randy Ulrich - 01-18-2019, 07:27 AM

RE: 37-610 Restoration - by Ron Ramirez - 01-18-2019, 07:31 AM

RE: 37-610 Restoration - by Randy Ulrich - 01-18-2019, 10:00 AM

RE: 37-610 Restoration - by Ron Ramirez - 01-18-2019, 10:26 AM

RE: 37-610 Restoration - by Randy Ulrich - 01-29-2019, 05:59 PM

RE: 37-610 Restoration - by morzh - 01-29-2019, 06:22 PM

RE: 37-610 Restoration - by klondike98 - 01-29-2019, 06:36 PM

RE: 37-610 Restoration - by Randy Ulrich - 02-01-2019, 12:52 PM

RE: 37-610 Restoration - by Ron Ramirez - 02-01-2019, 01:09 PM

RE: 37-610 Restoration - by Randy Ulrich - 02-01-2019, 04:19 PM

RE: 37-610 Restoration - by klondike98 - 02-01-2019, 06:47 PM

RE: 37-610 Restoration - by Randy Ulrich - 02-01-2019, 08:16 PM

RE: 37-610 Restoration - by Randy Ulrich - 02-23-2019, 05:40 AM

RE: 37-610 Restoration - by KCMike - 02-23-2019, 07:48 PM

RE: 37-610 Restoration - by Randy Ulrich - 02-25-2019, 11:56 AM

RE: 37-610 Restoration - by morzh - 02-25-2019, 01:08 PM

View a Printable Version

Users browsing this thread: 7 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me