41-221 nightmare

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

41-221 nightmare

Jim Dutridge
Senior Member

Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo State, Province, Country: OH

#21

02-25-2019, 05:10 PM

Well, I finished replacing the caps and any out of tolerance resistors. Also left some of the original wiring that did not have cracked insulation. It works and sounds good but I still need to install a fuse, line cap and do an alignment as the tracking is off.

[Image: https://i248.photobucket.com/albums/gg18...w4s417.jpg]

Also, the clip that holds the oscillator coil to the chassis is not there since the top portion of the coil form broke so there is no place to asttach it.

(This post was last modified: 02-25-2019, 05:11 PM by Jim Dutridge.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

41-221 nightmare - by Jim Dutridge - 02-02-2019, 12:28 PM

RE: 41-221 nightmare - by Phlogiston - 02-02-2019, 01:28 PM

RE: 41-221 nightmare - by tbone - 02-02-2019, 04:47 PM

RE: 41-221 nightmare - by morzh - 02-02-2019, 05:19 PM

RE: 41-221 nightmare - by Arran - 02-02-2019, 06:25 PM

RE: 41-221 nightmare - by morzh - 02-02-2019, 06:45 PM

RE: 41-221 nightmare - by Arran - 02-03-2019, 03:46 AM

RE: 41-221 nightmare - by amptramp - 02-04-2019, 11:30 PM

RE: 41-221 nightmare - by morzh - 02-04-2019, 11:59 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-07-2019, 06:02 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-17-2019, 01:41 PM

RE: 41-221 nightmare - by David - 02-17-2019, 03:35 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-19-2019, 05:17 PM

RE: 41-221 nightmare - by morzh - 02-19-2019, 05:46 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-19-2019, 07:31 PM

RE: 41-221 nightmare - by Ron Ramirez - 02-19-2019, 07:36 PM

RE: 41-221 nightmare - by mikethedruid - 02-19-2019, 10:00 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-20-2019, 05:26 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-22-2019, 10:04 PM

RE: 41-221 nightmare - by jcassity - 02-25-2019, 10:07 AM

RE: 41-221 nightmare - by Jim Dutridge - 02-25-2019, 05:10 PM

RE: 41-221 nightmare - by Jim Dutridge - 02-27-2019, 04:52 PM

RE: 41-221 nightmare - by morzh - 02-27-2019, 10:46 PM

RE: 41-221 nightmare - by Jim Dutridge - 03-04-2019, 05:27 PM

RE: 41-221 nightmare - by amptramp - 03-05-2019, 08:45 AM

RE: 41-221 nightmare - by Jim Dutridge - 03-10-2019, 10:17 AM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM

Who's Online

There are currently 3952 online users. [Complete List]
» 2 Member(s) | 3950 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me