Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Farm Radio 38 123
#21

Ok plan B.
Check the tuning cap for bend plates. If there is a bend one most or the time it would be one of the ones on the outside. You also use your ohm meter to measure the resistance across the cap BUT remember that it's in parallel w/ a coil that has a low resistance to start with. With that being said if it has a short it's going to be very low in resistance like something less than 1 ohm or less. Unshorted would be abt 3 or 4 ohms. Either section shorted would give you very poor reception.

The tuning cap is broken down into two sections, one section tunes the antenna circuit and the other tunes the oscillator. I don't have a chassis layout for this set only a diagram, it doesn't tell me which is which. If the cap checks out ok then I would try another 1A6.


As I mentioned before all voltages at the 1A6 look to be what I would expect except for pin 4. Should be a volt or two negative w/a high impedance meter.
No worries there is a plan C.


Happy Hunting!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco Farm Radio 38 123 - by RCFlyer - 02-21-2019, 01:42 AM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-21-2019, 11:26 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-21-2019, 06:27 PM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-21-2019, 07:47 PM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-22-2019, 11:29 PM
RE: Philco Farm Radio 38 123 - by 35Z5 - 02-23-2019, 12:37 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-23-2019, 12:53 AM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-23-2019, 01:56 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-23-2019, 02:24 AM
RE: Philco Farm Radio 38 123 - by Stall-U-Rated - 02-23-2019, 02:44 AM
RE: Philco Farm Radio 38 123 - by Arran - 02-23-2019, 05:48 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-24-2019, 12:31 AM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-24-2019, 01:18 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-25-2019, 12:40 AM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-26-2019, 12:00 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-28-2019, 01:47 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-28-2019, 02:01 AM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-28-2019, 11:13 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-28-2019, 03:30 PM
RE: Philco Farm Radio 38 123 - by Radioroslyn - 02-28-2019, 09:40 PM
RE: Philco Farm Radio 38 123 - by RCFlyer - 02-28-2019, 10:04 PM
RE: Philco Farm Radio 38 123 - by Stall-U-Rated - 03-01-2019, 12:23 AM
RE: Philco Farm Radio 38 123 - by RCFlyer - 03-01-2019, 03:02 PM



Users browsing this thread: 15 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 6169 online users. [Complete List]
» 1 Member(s) | 6168 Guest(s)
Avatar

>