RCA V-210 field coil removal

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

RCA V-210 field coil removal

Steve Davis
Phorum Expert

Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO

03-05-2019, 05:44 PM

I have not done an RCA speaker but I have done a couple of Philco speakers. The Philco speakers have step machined on the pole piece, so when pressed back in, it will self center. I suspect the RCA will be the same.

Steve

M R Radios C M Tubes

Find

« Next Oldest | Next Newest »

Messages In This Thread

RCA V-210 field coil removal - by Steve D - 03-05-2019, 05:07 PM

RE: RCA V-210 field coil removal - by Steve Davis - 03-05-2019, 05:44 PM

RE: RCA V-210 field coil removal - by Steve D - 03-08-2019, 05:15 PM

RE: RCA V-210 field coil removal - by Arran - 03-09-2019, 06:11 AM

RE: RCA V-210 field coil removal - by tbone - 03-09-2019, 10:24 AM

RE: RCA V-210 field coil removal - by morzh - 03-09-2019, 11:54 AM

RE: RCA V-210 field coil removal - by tbone - 03-09-2019, 01:48 PM

RE: RCA V-210 field coil removal - by Steve D - 03-10-2019, 12:52 PM

RE: RCA V-210 field coil removal - by Arran - 03-11-2019, 05:41 AM

RE: RCA V-210 field coil removal - by sdradioman - 03-11-2019, 07:17 AM

RE: RCA V-210 field coil removal - by Phlogiston - 03-11-2019, 11:36 AM

RE: RCA V-210 field coil removal - by morzh - 03-11-2019, 11:49 AM

RE: RCA V-210 field coil removal - by Steve D - 03-19-2019, 04:08 PM

RE: RCA V-210 field coil removal - by Steve D - 03-19-2019, 04:13 PM

RE: RCA V-210 field coil removal - by EdHolland - 03-19-2019, 09:29 PM

RE: RCA V-210 field coil removal - by Steve D - 03-21-2019, 09:09 AM

RE: RCA V-210 field coil removal - by Phlogiston - 03-21-2019, 11:38 AM

RE: RCA V-210 field coil removal - by Steve D - 03-23-2019, 05:46 PM

RE: RCA V-210 field coil removal - by klondike98 - 03-24-2019, 10:43 PM

RE: RCA V-210 field coil removal - by Steve D - 04-08-2019, 01:34 PM

RE: RCA V-210 field coil removal - by Steve D - 04-08-2019, 01:37 PM

RE: RCA V-210 field coil removal - by Steve D - 04-29-2019, 04:34 PM

RE: RCA V-210 field coil removal - by Steve D - 04-29-2019, 04:36 PM

RE: RCA V-210 field coil removal - by Steve D - 05-06-2019, 10:48 AM

RE: RCA V-210 field coil removal - by Steve D - 05-06-2019, 10:50 AM

RE: RCA V-210 field coil removal - by morzh - 05-06-2019, 11:19 AM

RE: RCA V-210 field coil removal - by sdradioman - 05-06-2019, 01:53 PM

RE: RCA V-210 field coil removal - by Steve D - 05-16-2019, 11:23 AM

View a Printable Version

Users browsing this thread: 8 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me