1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
AA5 hum
35Z5
Member
***
Posts: 184
Threads: 3
Joined: Feb 2018
City: Chesapeake VA
#16

03-17-2019, 05:55 PM
I can't visualise the output transformer being a source of hum originates from insufficient filtering of power supply. A few transformers did have hum buck windings but if P/S is filtered sufficiently it isn't needed.
Tom
(This post was last modified: 03-17-2019, 05:56 PM by 35Z5.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
AA5 hum - by fenbach - 10-18-2018, 11:02 PM
RE: AA5 hum - by Radioroslyn - 10-18-2018, 11:28 PM
RE: AA5 hum - by Jayce - 10-19-2018, 12:05 AM
RE: AA5 hum - by Chas - 10-19-2018, 12:09 AM
RE: AA5 hum - by fenbach - 10-19-2018, 08:18 PM
RE: AA5 hum - by fenbach - 10-19-2018, 08:20 PM
RE: AA5 hum - by Chas - 10-20-2018, 12:04 AM
RE: AA5 hum - by gregb - 10-21-2018, 12:04 AM
RE: AA5 hum - by David - 11-04-2018, 03:20 PM
RE: AA5 hum - by Jayce - 11-04-2018, 09:24 PM
RE: AA5 hum - by 35Z5 - 11-05-2018, 09:57 AM
RE: AA5 hum - by morzh - 11-05-2018, 10:48 AM
RE: AA5 hum - by Squire - 11-08-2018, 01:12 AM
RE: AA5 hum - by fenbach - 03-16-2019, 11:12 PM
RE: AA5 hum - by Arran - 03-16-2019, 11:49 PM
RE: AA5 hum - by 35Z5 - 03-17-2019, 05:55 PM
RE: AA5 hum - by fenbach - 03-23-2019, 07:54 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4493 online users. [Complete List]
» 1 Member(s) | 4492 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)