1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Alignment Questions.
Chas
Senior Member
****
Posts: 693
Threads: 8
Joined: Apr 2018
City: S. Dartmouth State, Province, Country: MA
#2

03-19-2019, 05:18 PM
Special Section VIII is a front end to the Riders Volume VIII, not reproduced in Nostalgia. However going with conventional alignment, do as for any typical AA5 set.

Do check the band switch and the antenna coils for BC band. Most likely one is open. Or miss-wire during the shotgunning.

Chas
Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
Find
« Next Oldest | Next Newest »


Messages In This Thread
Alignment Questions. - by Eric - 03-19-2019, 05:05 PM
RE: Alignment Questions. - by Chas - 03-19-2019, 05:18 PM
RE: Alignment Questions. - by Eric - 03-20-2019, 09:36 AM
RE: Alignment Questions. - by Chas - 03-20-2019, 11:03 AM
RE: Alignment Questions. - by radio63 - 03-20-2019, 03:13 PM
RE: Alignment Questions. - by Eric - 03-21-2019, 10:42 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6016 online users. [Complete List]
» 1 Member(s) | 6015 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)