Substitute higher secondary a.c. voltages

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

~~Jake Blake~~
Banned

Posts: 816
Threads: 25
Joined: Mar 2014
City: Louisville, KY

04-04-2019, 09:44 PM

Has anyone ever used a power transformer as a substitute in a radio, that had a little higher high voltage secondary than the original, and replaced a few key resistors to bring the d.c. supply voltages back in line to what they're supposed to be?

I'm curious about doing this with the 39-6 C I, and replace resistors, (part numbers) 19, 23 and 24. Also maybe insert some resistance in the output transformer / output plate connections for the 41 tube? Has anyone done this successfully?

Jake

Find

« Next Oldest | Next Newest »

Messages In This Thread

Substitute higher secondary a.c. voltages - by Jake Blake - 04-04-2019, 09:44 PM

RE: Substitute higher secondary a.c. voltages - by Radioroslyn - 04-04-2019, 10:29 PM

RE: Substitute higher secondary a.c. voltages - by morzh - 04-05-2019, 08:45 AM

RE: Substitute higher secondary a.c. voltages - by 35Z5 - 04-05-2019, 08:48 AM

RE: Substitute higher secondary a.c. voltages - by morzh - 04-05-2019, 11:24 AM

RE: Substitute higher secondary a.c. voltages - by 35Z5 - 04-05-2019, 04:08 PM

RE: Substitute higher secondary a.c. voltages - by Radioroslyn - 04-05-2019, 06:08 PM

RE: Substitute higher secondary a.c. voltages - by morzh - 04-05-2019, 07:54 PM

RE: Substitute higher secondary a.c. voltages - by Jake Blake - 04-05-2019, 08:16 PM

RE: Substitute higher secondary a.c. voltages - by morzh - 04-05-2019, 08:38 PM

RE: Substitute higher secondary a.c. voltages - by 35Z5 - 04-05-2019, 09:48 PM

RE: Substitute higher secondary a.c. voltages - by Radioroslyn - 04-05-2019, 10:52 PM

RE: Substitute higher secondary a.c. voltages - by Jake Blake - 04-05-2019, 11:23 PM

RE: Substitute higher secondary a.c. voltages - by 35Z5 - 04-06-2019, 10:18 AM

RE: Substitute higher secondary a.c. voltages - by morzh - 04-06-2019, 10:23 AM

RE: Substitute higher secondary a.c. voltages - by Jake Blake - 04-06-2019, 12:03 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me