Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Fisher 500C restoration
#46

(03-31-2019, 10:55 PM)EdHolland Wrote:  I might play with re-forming, just for the learning as I've never tried it. As for the amp, the new caps are paid for and very nice quality, no doubt they will see good service.

Don't waste your time. The results are usually very short term. Even then ESR is likely to go up. The problem is usually being the electrolyte has become un-evenly distributed and this causes the oxide layer to also be uneven IF you can get it to reform.

We used to turn them upside down before reforming - actually makes sense - also a waste of time.

After you have a "bad" cap removed, don't invest the time putting it back.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/


Messages In This Thread
Fisher 500C restoration - by EdHolland - 02-03-2019, 06:03 PM
RE: Fisher 500C restoration - by morzh - 02-03-2019, 06:11 PM
RE: Fisher 500C restoration - by Ron Ramirez - 02-03-2019, 06:50 PM
RE: Fisher 500C restoration - by EdHolland - 02-03-2019, 07:25 PM
RE: Fisher 500C restoration - by Ron Ramirez - 02-03-2019, 07:58 PM
RE: Fisher 500C restoration - by EdHolland - 02-04-2019, 09:07 PM
RE: Fisher 500C restoration - by EdHolland - 02-20-2019, 05:07 PM
RE: Fisher 500C restoration - by KCMike - 02-20-2019, 06:03 PM
RE: Fisher 500C restoration - by Ron Ramirez - 02-20-2019, 11:11 PM
RE: Fisher 500C restoration - by EdHolland - 02-21-2019, 03:10 PM
RE: Fisher 500C restoration - by EdHolland - 02-25-2019, 06:46 PM
RE: Fisher 500C restoration - by EdHolland - 03-01-2019, 05:02 PM
RE: Fisher 500C restoration - by EdHolland - 03-15-2019, 08:22 PM
RE: Fisher 500C restoration - by TV MAN - 03-16-2019, 09:20 AM
RE: Fisher 500C restoration - by EdHolland - 03-17-2019, 08:35 PM
RE: Fisher 500C restoration - by EdHolland - 03-18-2019, 10:29 PM
RE: Fisher 500C restoration - by EdHolland - 03-20-2019, 09:27 PM
RE: Fisher 500C restoration - by EdHolland - 03-21-2019, 03:23 PM
RE: Fisher 500C restoration - by EdHolland - 03-22-2019, 10:44 PM
RE: Fisher 500C restoration - by EdHolland - 03-22-2019, 11:12 PM
RE: Fisher 500C restoration - by morzh - 03-23-2019, 11:45 AM
RE: Fisher 500C restoration - by morzh - 03-23-2019, 03:40 PM
RE: Fisher 500C restoration - by EdHolland - 03-23-2019, 08:23 PM
RE: Fisher 500C restoration - by morzh - 03-23-2019, 08:29 PM
RE: Fisher 500C restoration - by Ron Ramirez - 03-23-2019, 10:20 PM
RE: Fisher 500C restoration - by EdHolland - 03-23-2019, 10:22 PM
RE: Fisher 500C restoration - by EdHolland - 03-23-2019, 11:09 PM
RE: Fisher 500C restoration - by morzh - 03-24-2019, 10:45 AM
RE: Fisher 500C restoration - by Phlogiston - 03-24-2019, 01:11 PM
RE: Fisher 500C restoration - by EdHolland - 03-24-2019, 02:15 PM
RE: Fisher 500C restoration - by morzh - 03-24-2019, 02:18 PM
RE: Fisher 500C restoration - by EdHolland - 03-24-2019, 10:56 PM
RE: Fisher 500C restoration - by morzh - 03-25-2019, 09:07 AM
RE: Fisher 500C restoration - by EdHolland - 03-27-2019, 01:20 PM
RE: Fisher 500C restoration - by EdHolland - 03-30-2019, 07:49 PM
RE: Fisher 500C restoration - by morzh - 03-31-2019, 10:51 AM
RE: Fisher 500C restoration - by EdHolland - 03-31-2019, 07:31 PM
RE: Fisher 500C restoration - by EdHolland - 03-31-2019, 09:59 PM
RE: Fisher 500C restoration - by morzh - 03-31-2019, 10:23 PM
RE: Fisher 500C restoration - by EdHolland - 03-31-2019, 10:55 PM
RE: Fisher 500C restoration - by morzh - 04-01-2019, 08:32 AM
RE: Fisher 500C restoration - by TV MAN - 04-02-2019, 11:38 AM
RE: Fisher 500C restoration - by Ron Ramirez - 04-02-2019, 12:30 PM
RE: Fisher 500C restoration - by EdHolland - 04-07-2019, 10:10 PM
RE: Fisher 500C restoration - by EdHolland - 04-14-2019, 10:04 PM
RE: Fisher 500C restoration - by Phlogiston - 04-15-2019, 11:41 AM
RE: Fisher 500C restoration - by EdHolland - 04-15-2019, 02:51 PM
RE: Fisher 500C restoration - by Phlogiston - 04-15-2019, 06:23 PM
RE: Fisher 500C restoration - by EdHolland - 04-21-2019, 02:36 AM
RE: Fisher 500C restoration - by EdHolland - 04-21-2019, 02:45 PM
RE: Fisher 500C restoration - by EdHolland - 04-21-2019, 09:44 PM
RE: Fisher 500C restoration - by EdHolland - 04-23-2019, 12:51 PM
RE: Fisher 500C restoration - by EdHolland - 04-25-2019, 03:57 PM
RE: Fisher 500C restoration - by EdHolland - 04-30-2019, 08:05 PM
RE: Fisher 500C restoration - by EdHolland - 05-05-2019, 05:35 PM
RE: Fisher 500C restoration - by EdHolland - 05-12-2019, 03:35 PM
RE: Fisher 500C restoration - by Ron Ramirez - 05-12-2019, 04:26 PM
RE: Fisher 500C restoration - by EdHolland - 05-12-2019, 07:15 PM
RE: Fisher 500C restoration - by EdHolland - 05-19-2019, 09:07 PM
RE: Fisher 500C restoration - by morzh - 05-20-2019, 02:37 PM
RE: Fisher 500C restoration - by EdHolland - 05-20-2019, 06:05 PM
RE: Fisher 500C restoration - by Ron Ramirez - 05-20-2019, 08:57 PM
RE: Fisher 500C restoration - by morzh - 05-21-2019, 12:22 PM
RE: Fisher 500C restoration - by EdHolland - 05-23-2019, 12:07 AM
RE: Fisher 500C restoration - by EdHolland - 05-23-2019, 01:30 AM
RE: Fisher 500C restoration - by EdHolland - 05-24-2019, 03:28 PM
RE: Fisher 500C restoration - by Ron Ramirez - 05-25-2019, 06:45 PM
RE: Fisher 500C restoration - by EdHolland - 05-25-2019, 09:44 PM
RE: Fisher 500C restoration - by EdHolland - 05-29-2019, 11:10 AM
RE: Fisher 500C restoration - by EdHolland - 05-30-2019, 10:42 AM
RE: Fisher 500C restoration - by EdHolland - 06-01-2019, 11:49 PM
RE: Fisher 500C restoration - by Ron Ramirez - 06-02-2019, 08:07 AM
RE: Fisher 500C restoration - by EdHolland - 06-02-2019, 11:09 PM
RE: Fisher 500C restoration - by EdHolland - 06-08-2019, 11:47 PM
RE: Fisher 500C restoration - by EdHolland - 06-10-2019, 04:04 PM
RE: Fisher 500C restoration - by EdHolland - 07-10-2019, 08:52 PM
RE: Fisher 500C restoration - by Ron Ramirez - 07-12-2019, 10:43 PM
RE: Fisher 500C restoration - by EdHolland - 07-14-2019, 11:02 PM
RE: Fisher 500C restoration - by EdHolland - 07-20-2019, 11:18 PM
RE: Fisher 500C restoration - by EdHolland - 07-24-2019, 01:51 AM
RE: Fisher 500C restoration - by gregb - 07-24-2019, 07:18 AM
RE: Fisher 500C restoration - by EdHolland - 07-24-2019, 05:48 PM
RE: Fisher 500C restoration - by rfeenstra - 07-24-2019, 06:24 PM
RE: Fisher 500C restoration - by EdHolland - 07-28-2019, 12:00 AM
RE: Fisher 500C restoration - by EdHolland - 07-28-2019, 11:08 PM
RE: Fisher 500C restoration - by morzh - 07-29-2019, 07:55 AM
RE: Fisher 500C restoration - by EdHolland - 07-31-2019, 11:43 AM
RE: Fisher 500C restoration - by Phlogiston - 07-31-2019, 12:21 PM
RE: Fisher 500C restoration - by EdHolland - 07-31-2019, 08:46 PM
RE: Fisher 500C restoration - by Joeztech - 08-02-2019, 07:47 AM
RE: Fisher 500C restoration - by Joeztech - 08-02-2019, 09:58 AM
RE: Fisher 500C restoration - by EdHolland - 08-04-2019, 04:31 PM
RE: Fisher 500C restoration - by Phlogiston - 08-05-2019, 12:01 AM
RE: Fisher 500C restoration - by EdHolland - 08-05-2019, 05:01 AM
RE: Fisher 500C restoration - by EdHolland - 08-26-2019, 12:09 AM
RE: Fisher 500C restoration - by doc_zap - 09-10-2019, 11:53 PM
RE: Fisher 500C restoration - by EdHolland - 09-11-2019, 12:24 PM



Users browsing this thread: 31 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM

[-]
Who's Online
There are currently no members online.

>