1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 49-607 Filter Capacitor
Ed49-607
Junior Member
**
Posts: 3
Threads: 1
Joined: Apr 2019
City: Lake Forest State, Province, Country: Illinois
#3

04-30-2019, 08:50 AM
Morzh,

Thanks for the information and suggestions. I'm only using electrolytic caps to replace the filter capacitors, 60-30-30-10 as I recall. The rest are film caps so not too crowded in the chassis. I'll check the resistor after rectifier/filter caps as you suggest. Good idea. Thanks.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 49-607 Filter Capacitor - by Ed49-607 - 04-29-2019, 02:15 PM
RE: Philco 49-607 Filter Capacitor - by morzh - 04-29-2019, 03:32 PM
RE: Philco 49-607 Filter Capacitor - by Ed49-607 - 04-30-2019, 08:50 AM
RE: Philco 49-607 Filter Capacitor - by WyTex - 05-02-2019, 08:00 AM
RE: Philco 49-607 Filter Capacitor - by Ed49-607 - 05-02-2019, 02:36 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7826 online users. [Complete List]
» 2 Member(s) | 7824 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration