Philco 20 Restoration

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 20 Restoration

GarySP
Super Moderator

Posts: 1,976
Threads: 147
Joined: Jan 2013
City: Westland, MI

#30

05-04-2019, 06:13 PM

Yes Ron, thanks! I had forgotten all about this thread. Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 20 Restoration - by Steve Davis - 02-26-2018, 11:21 PM

RE: Philco 20 Restoration - by morzh - 02-26-2018, 11:56 PM

RE: Philco 20 Restoration - by Steve Davis - 02-27-2018, 12:44 AM

RE: Philco 20 Restoration - by morzh - 02-27-2018, 12:50 AM

RE: Philco 20 Restoration - by Steve Davis - 02-27-2018, 12:00 PM

RE: Philco 20 Restoration - by Nathan Slingerland - 02-27-2018, 12:03 PM

RE: Philco 20 Restoration - by Steve Davis - 02-27-2018, 12:09 PM

RE: Philco 20 Restoration - by Nathan Slingerland - 02-27-2018, 12:14 PM

RE: Philco 20 Restoration - by Steve Davis - 02-27-2018, 01:08 PM

RE: Philco 20 Restoration - by Steve Davis - 02-27-2018, 09:54 PM

RE: Philco 20 Restoration - by Steve Davis - 03-04-2018, 10:50 AM

RE: Philco 20 Restoration - by morzh - 03-04-2018, 11:16 AM

RE: Philco 20 Restoration - by Steve Davis - 03-04-2018, 11:47 AM

RE: Philco 20 Restoration - by morzh - 03-04-2018, 12:43 PM

RE: Philco 20 Restoration - by Arran - 03-04-2018, 07:43 PM

RE: Philco 20 Restoration - by GarySP - 03-27-2018, 11:39 AM

RE: Philco 20 Restoration - by Steve Davis - 03-27-2018, 06:37 PM

RE: Philco 20 Restoration - by Ron Ramirez - 03-27-2018, 07:07 PM

RE: Philco 20 Restoration - by Steve Davis - 03-27-2018, 07:34 PM

RE: Philco 20 Restoration - by Ron Ramirez - 03-27-2018, 07:55 PM

RE: Philco 20 Restoration - by GarySP - 03-28-2018, 08:39 AM

RE: Philco 20 Restoration - by Steve Davis - 03-28-2018, 06:45 PM

RE: Philco 20 Restoration - by GarySP - 03-29-2018, 08:46 AM

RE: Philco 20 Restoration - by GarySP - 03-31-2018, 02:33 PM

RE: Philco 20 Restoration - by Steve Davis - 04-01-2018, 09:17 AM

RE: Philco 20 Restoration - by mg34.42 - 04-28-2019, 11:27 PM

RE: Philco 20 Restoration - by Radioroslyn - 04-29-2019, 12:41 AM

RE: Philco 20 Restoration - by Ron Ramirez - 05-04-2019, 01:08 PM

RE: Philco 20 Restoration - by Radioroslyn - 05-04-2019, 04:51 PM

RE: Philco 20 Restoration - by GarySP - 05-04-2019, 06:13 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

Who's Online
There are currently no members online.