Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What do I have here?
#5

Hi James and welcome.
To answer your question I'll ask you a question, what Philco model are you servicing??
Part numbers are sometimes hard to sort out when you don't not know what they go to.

Not sure if the post goes w/the 1st three maybe Bob can move it and change it to a separate thread.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
What do I have here? - by Mark8100 - 05-07-2019, 01:24 AM
RE: [split] What do I have here? - by klondike98 - 05-07-2019, 09:09 AM
RE: What do I have here? - by jesushisway - 05-07-2019, 06:06 PM
RE: What do I have here? - by Radioroslyn - 05-07-2019, 07:40 PM
RE: What do I have here? - by Mark8100 - 05-07-2019, 08:46 PM
RE: What do I have here? - by klondike98 - 05-07-2019, 09:03 PM
RE: What do I have here? - by Mark8100 - 05-07-2019, 10:18 PM
RE: What do I have here? - by klondike98 - 05-08-2019, 09:13 AM
RE: What do I have here? - by Mark8100 - 05-14-2019, 09:37 AM
RE: What do I have here? - by Mark8100 - 05-14-2019, 10:07 AM
RE: What do I have here? - by klondike98 - 05-14-2019, 04:59 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4866 online users. [Complete List]
» 1 Member(s) | 4865 Guest(s)
Avatar

>