Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 20, 21, 90 or what?
#9

Hi Robin and welcome to the fray,
I think Mike has the answer. Chassis is a 20. If it were a 21 it would have a large round filter cap. The 20 uses several in a tin can like this chassis. The 90 would have a singe section volume control only the older non avc sets use the dual control. I would suspect the knob on the right is to adjust the tone the 20/21 didn't have that adjustment.
Cabinet is for a 90. The holes for the chassis to the wooden base don't align. The 20/21 only use three bolts the 70/90 uses four.

If you could post a pic or two of the top and bottom of the chassis and the base board that arn't so close up I can a little bit more abt it.

Best Regard's

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 20, 21, 90 or what? - by Robin in Kansas - 05-22-2019, 12:00 PM
RE: Philco 20, 21, 90 or what? - by klondike98 - 05-22-2019, 12:14 PM
RE: Philco 20, 21, 90 or what? - by morzh - 05-22-2019, 01:11 PM
RE: Philco 20, 21, 90 or what? - by klondike98 - 05-22-2019, 01:15 PM
RE: Philco 20, 21, 90 or what? - by morzh - 05-22-2019, 01:16 PM
RE: Philco 20, 21, 90 or what? - by klondike98 - 05-22-2019, 01:34 PM
RE: Philco 20, 21, 90 or what? - by Radioroslyn - 05-22-2019, 02:29 PM
RE: Philco 20, 21, 90 or what? - by Steve Davis - 05-22-2019, 02:30 PM
RE: Philco 20, 21, 90 or what? - by klondike98 - 05-22-2019, 02:35 PM
RE: Philco 20, 21, 90 or what? - by morzh - 05-22-2019, 02:50 PM
RE: Philco 20, 21, 90 or what? - by Ron Ramirez - 05-22-2019, 05:43 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4832 online users. [Complete List]
» 1 Member(s) | 4831 Guest(s)
Avatar

>