Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 46-132
#5

Thanks very much. That helps a lot.

NOW . . . . I am fairly knowledgeable about electronics . . . . from a theoretical standpoint. But I am no competent technician or restorer. How much would it cost to restore one of these and maybe convert it to a AC power? I understand that much of the cost would depend on the condition once someone gets into it. Assuming that none of the parts are missing, how much do people charge for restore this? The cosmetics are fine so it just requires work on the electronics. Again, just the order of magnitude would be helpful (e.g. $100 - $200, $200 - $300, etc).

Thanks for your feedback. Once I get an idea about this I suppose my next question will be who are some people who might be interested in doing this.

DANNO


Messages In This Thread
Model 46-132 - by danno - 11-29-2010, 01:26 AM
Re: Model 46-132 - by dos0711 - 11-29-2010, 02:55 PM
Re: Model 46-132 - by danno - 11-30-2010, 10:47 AM
Re: Model 46-132 - by Chuck Schwark - 11-30-2010, 10:54 AM
Re: Model 46-132 - by danno - 11-30-2010, 03:46 PM
Re: Model 46-132 - by Chuck Schwark - 11-30-2010, 04:06 PM
Re: Model 46-132 - by TexMac - 12-05-2010, 05:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5910 online users. [Complete List]
» 2 Member(s) | 5908 Guest(s)
AvatarAvatar

>