Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Need help on 40-180 chassis
#16

OK, just got everything back together and did what morzh said to do. So with the signal generator hooked up to the antenna screw thru a .1 cap and volumn all the way up I put 40 AC volts of signal to the plates. Then I connect the voltmeter to the secondary side of the OT and had at times .7 volts  max and it would drop to 0 and fluctuate from 0 to .7 volts. So looks like my problem is the transformer is not putting out. I will be looking for a replacement. Learning experience for me so thanks mortzh. I'll know more how to test these in the future. Once I find another I'll post the results.


Messages In This Thread
Need help on 40-180 chassis - by BillT52 - 06-06-2019, 08:45 AM
RE: Need help on 40-180 chassis - by morzh - 06-06-2019, 11:11 AM
RE: Need help on 40-180 chassis - by klondike98 - 06-06-2019, 12:18 PM
RE: Need help on 40-180 chassis - by LarryFS - 06-06-2019, 01:12 PM
RE: Need help on 40-180 chassis - by morzh - 06-06-2019, 02:21 PM
RE: Need help on 40-180 chassis - by BillT52 - 06-06-2019, 02:54 PM
RE: Need help on 40-180 chassis - by LarryFS - 06-06-2019, 06:03 PM
RE: Need help on 40-180 chassis - by morzh - 06-06-2019, 08:40 PM
RE: Need help on 40-180 chassis - by madsowry - 06-06-2019, 09:26 PM
RE: Need help on 40-180 chassis - by morzh - 06-06-2019, 09:56 PM
RE: Need help on 40-180 chassis - by BillT52 - 06-07-2019, 09:06 AM
RE: Need help on 40-180 chassis - by morzh - 06-07-2019, 09:54 AM
RE: Need help on 40-180 chassis - by BillT52 - 06-07-2019, 10:30 AM
RE: Need help on 40-180 chassis - by morzh - 06-07-2019, 10:39 AM
RE: Need help on 40-180 chassis - by BillT52 - 06-07-2019, 04:04 PM
RE: Need help on 40-180 chassis - by BillT52 - 06-07-2019, 05:42 PM
RE: Need help on 40-180 chassis - by morzh - 06-07-2019, 09:23 PM
RE: Need help on 40-180 chassis - by BillT52 - 06-07-2019, 10:29 PM
RE: Need help on 40-180 chassis - by morzh - 06-07-2019, 11:00 PM
RE: Need help on 40-180 chassis - by BillT52 - 06-08-2019, 06:54 AM
RE: Need help on 40-180 chassis - by Radioroslyn - 06-08-2019, 10:47 AM
RE: Need help on 40-180 chassis - by morzh - 06-08-2019, 11:06 AM
RE: Need help on 40-180 chassis - by BillT52 - 06-08-2019, 12:37 PM
RE: Need help on 40-180 chassis - by Radioroslyn - 06-08-2019, 01:24 PM
RE: Need help on 40-180 chassis - by morzh - 06-08-2019, 02:44 PM
RE: Need help on 40-180 chassis - by Radioroslyn - 06-08-2019, 07:06 PM
RE: Need help on 40-180 chassis - by BillT52 - 06-25-2019, 11:36 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 7824 online users. [Complete List]
» 1 Member(s) | 7823 Guest(s)
Avatar

>