60b Chassis attachment

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

60b Chassis attachment

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

07-21-2019, 08:21 AM

Not sure but it doesn't look like the bakelite blocks have been restuffed nor have the 2 electrolytic caps. Testing these is an afford in futility, would both just replace. I'd flip over a few of the blocks just to check. If that square 5w resistor is 70 ohms it's kind low should be 200 ohms. The chassis bolts are 1/4" with a thread pitch of 10 per inch (really course) 5/16 hex head w/a slot. Abt an inch and a half long.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

(This post was last modified: 07-21-2019, 08:24 AM by Radioroslyn.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

60b Chassis attachment - by atlghosthunter - 07-21-2019, 02:09 AM

RE: 60b Chassis attachment - by Radioroslyn - 07-21-2019, 08:21 AM

RE: 60b Chassis attachment - by atlghosthunter - 07-21-2019, 12:00 PM

RE: 60b Chassis attachment - by Radioroslyn - 07-21-2019, 12:25 PM

RE: 60b Chassis attachment - by atlghosthunter - 07-21-2019, 02:27 PM

RE: 60b Chassis attachment - by Ed Locker - 07-22-2019, 09:29 AM

RE: 60b Chassis attachment - by Radioroslyn - 07-29-2019, 12:18 PM

RE: 60b Chassis attachment - by atlghosthunter - 08-13-2019, 10:40 AM

RE: 60b Chassis attachment - by atlghosthunter - 08-13-2019, 10:42 AM

RE: 60b Chassis attachment - by atlghosthunter - 08-13-2019, 08:25 PM

RE: 60b Chassis attachment - by atlghosthunter - 08-13-2019, 08:50 PM

RE: 60b Chassis attachment - by atlghosthunter - 08-13-2019, 11:26 PM

RE: 60b Chassis attachment - by atlghosthunter - 08-14-2019, 08:20 PM

RE: 60b Chassis attachment - by Jake Blake - 08-14-2019, 09:15 PM

RE: 60b Chassis attachment - by atlghosthunter - 08-17-2019, 12:11 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

Who's Online

There are currently 7988 online users. [Complete List]
» 1 Member(s) | 7987 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me