1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
PHILCO 610 UNUSUAL BEHAVIOR
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#6

07-23-2019, 09:14 AM
The old skool method is use your screwdriver to touch the ungrounded side of the trimmers till you find the one that shift the osc frequency. The one @ the front corner of the chassis is to set the low end of the bcb.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
PHILCO 610 UNUSUAL BEHAVIOR - by SJKEPKE - 07-22-2019, 04:10 PM
RE: PHILCO 610 UNUSUAL BEHAVIOR - by Radioroslyn - 07-22-2019, 08:35 PM
RE: PHILCO 610 UNUSUAL BEHAVIOR - by SJKEPKE - 07-22-2019, 08:48 PM
RE: PHILCO 610 UNUSUAL BEHAVIOR - by Radioroslyn - 07-22-2019, 11:04 PM
RE: PHILCO 610 UNUSUAL BEHAVIOR - by SJKEPKE - 07-22-2019, 11:32 PM
RE: PHILCO 610 UNUSUAL BEHAVIOR - by Radioroslyn - 07-23-2019, 09:14 AM
RE: PHILCO 610 UNUSUAL BEHAVIOR - by SJKEPKE - 07-23-2019, 10:40 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration