1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
What do I have...
Kico
Junior Member
**
Posts: 19
Threads: 3
Joined: Dec 2010
City: Tampa, FL
#5

12-28-2010, 10:13 AM
7estatdef Wrote:You may want to search this site for similar models like model 80,84,600, 57,37-84.
Terry

Thanks Terry,

Whew...there's a lot here. I was wondering if anybody has compiled a component list (caps/resistors, etc.) needed for rebuilding an 84B they could post or send me? My eyes are not what they used to be, and reading the actual and schematic values is difficult. I'd like make sure I have the correct parts before I place an order.

Also, could someone on the forum link me to the correct schematic for this radio...thanks.
Best regards,
Kico

"I whisper, but my horse still doesn't listen."
Find
« Next Oldest | Next Newest »


Messages In This Thread
What do I have... - by Kico - 12-26-2010, 08:54 AM
Re: What do I have... - by Ron Ramirez - 12-26-2010, 09:08 AM
Re: What do I have... - by Kico - 12-26-2010, 01:48 PM
Re: What do I have... - by 7estatdef - 12-26-2010, 04:54 PM
Re: What do I have... - by Kico - 12-28-2010, 10:13 AM
Re: What do I have... - by Ron Ramirez - 12-28-2010, 01:16 PM
Re: What do I have... - by Kico - 12-28-2010, 06:33 PM
Re: What do I have... - by gary rabbitt - 01-06-2011, 01:52 AM
Re: What do I have... - by Ron Ramirez - 01-06-2011, 01:10 PM
Re: What do I have... - by gary rabbitt - 01-06-2011, 01:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4563 online users. [Complete List]
» 1 Member(s) | 4562 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios