Starting on the Philco 610 from 1936

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Starting on the Philco 610 from 1936

Radioroslyn
Phorum Expert

Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

10-11-2019, 11:03 PM

It was to dampen vibration to the chassis. At the back of some of the chassis's they have square gum rubber mounts at the corners. Sorted floating it on rubber. If the front ones are bad the shafts and dial won't set in there proper positions.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Starting on the Philco 610 from 1936 - by Jake Blake - 10-11-2019, 04:04 PM

RE: Starting on the Philco 610 from 1936 - by klondike98 - 10-11-2019, 04:43 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-11-2019, 05:35 PM

RE: Starting on the Philco 610 from 1936 - by Simon Wa3uay - 10-11-2019, 08:44 PM

RE: Starting on the Philco 610 from 1936 - by Radioroslyn - 10-11-2019, 11:03 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 08:32 AM

RE: Starting on the Philco 610 from 1936 - by klondike98 - 10-12-2019, 09:13 AM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 10:35 AM

RE: Starting on the Philco 610 from 1936 - by Radioroslyn - 10-12-2019, 02:25 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 02:32 PM

RE: Starting on the Philco 610 from 1936 - by Chas - 10-12-2019, 02:48 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 03:02 PM

RE: Starting on the Philco 610 from 1936 - by Steve Davis - 10-12-2019, 07:12 PM

RE: Starting on the Philco 610 from 1936 - by Simon Wa3uay - 10-12-2019, 07:16 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 07:16 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 10:22 PM

RE: Starting on the Philco 610 from 1936 - by mikethedruid - 10-13-2019, 02:41 AM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-13-2019, 08:45 AM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-13-2019, 09:07 AM

RE: Starting on the Philco 610 from 1936 - by mikethedruid - 10-13-2019, 03:30 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-13-2019, 04:40 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-14-2019, 08:46 PM

RE: Starting on the Philco 610 from 1936 - by klondike98 - 10-14-2019, 09:15 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-14-2019, 09:49 PM

RE: Starting on the Philco 610 from 1936 - by mikethedruid - 10-14-2019, 11:20 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-15-2019, 08:50 AM

RE: Starting on the Philco 610 from 1936 - by Ron Ramirez - 10-15-2019, 12:00 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-15-2019, 02:43 PM

RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-15-2019, 11:47 PM

View a Printable Version

Users browsing this thread: 9 Guest(s)

Recent Posts
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM

Who's Online

There are currently 3506 online users. [Complete List]
» 2 Member(s) | 3504 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me