Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco model 84 1/35
#7

The 84B is looking a little better.
Added some grille cloth and veneer to the edges. The grille cloth came in from RD and this one seemed the match the original the best (pattern) color is a little too gold. May add a touch of toner to give it a little more of a copper look. Service the chassis and works good (could use some better 77's).
Next is stripping and staining the patches.


Attached Files Image(s)
   

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco model 84 1/35 - by Radioroslyn - 09-22-2019, 07:14 PM
RE: Philco model 84 1/35 - by sdradioman - 09-23-2019, 08:07 AM
RE: Philco model 84 1/35 - by Ron Ramirez - 09-23-2019, 08:08 AM
RE: Philco model 84 1/35 - by Radioroslyn - 09-23-2019, 10:32 AM
RE: Philco model 84 1/35 - by Ron Ramirez - 09-23-2019, 02:07 PM
RE: Philco model 84 1/35 - by Radioroslyn - 09-23-2019, 02:26 PM
RE: Philco model 84 1/35 - by Radioroslyn - 10-13-2019, 01:11 PM
RE: Philco model 84 1/35 - by Radioroslyn - 06-17-2020, 09:03 AM
RE: Philco model 84 1/35 - by morzh - 06-17-2020, 09:58 AM
RE: Philco model 84 1/35 - by Nathan Slingerland - 06-17-2020, 10:25 AM
RE: Philco model 84 1/35 - by RodB - 06-17-2020, 10:29 AM
RE: Philco model 84 1/35 - by Radioroslyn - 06-17-2020, 12:46 PM
RE: Philco model 84 1/35 - by klondike98 - 06-18-2020, 11:23 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Hi Bridcarl +1 on the others.  Pin 6 of the 7C6 is the AVC Diode so it is appropriate that that pin 4 of the coil con...MrFixr55 — 07:30 AM
462ron
Joseph, this is beyond awesome. A lot of thought and engineering went into this and you hit a home run! Now I must save ...462ron — 07:27 AM
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM

[-]
Who's Online
There are currently no members online.

>