Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Loose wire...
#4

Morning !
Looks like it should go over the to pin 4 or 5 ( should be hooked together ) of the 77 mixer tube.
It's part of the oscillator feedback circuit. It's common on these set of the feedback winding to
rot and on open. Your wire may have been disconnected to troubleshoot the coil.
Terry
ps Replace your filter condenser both sections lest you want to replace both section of the filter the 80 tube and the power transformer later!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Loose wire... - by Kico - 01-03-2011, 08:50 AM
Re: Loose wire... - by 7estatdef - 01-03-2011, 09:08 AM
Re: Loose wire... - by Kico - 01-03-2011, 09:24 AM
Re: Loose wire... - by 7estatdef - 01-03-2011, 11:14 AM
Re: Loose wire... - by Kico - 01-03-2011, 11:33 AM
Re: Loose wire... - by 7estatdef - 01-03-2011, 02:01 PM
Re: Loose wire... - by Kico - 01-05-2011, 04:47 PM
Re: Loose wire... - by 7estatdef - 01-05-2011, 05:16 PM
Re: Loose wire... - by gary rabbitt - 01-05-2011, 10:18 PM
Re: Loose wire... - by gary rabbitt - 01-06-2011, 12:02 AM
Re: Loose wire... - by Kico - 01-06-2011, 02:19 PM
Re: Loose wire... - by 7estatdef - 01-06-2011, 06:34 PM
Re: Loose wire... - by Kico - 01-06-2011, 07:51 PM
Re: Loose wire... - by 7estatdef - 01-06-2011, 08:33 PM
Re: Loose wire... - by Kico - 01-06-2011, 08:47 PM
Re: Loose wire... - by 7estatdef - 01-06-2011, 09:32 PM
Re: Loose wire... - by Kico - 01-07-2011, 03:01 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM

[-]
Who's Online
There are currently 2280 online users. [Complete List]
» 2 Member(s) | 2278 Guest(s)
AvatarAvatar

>