Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What do I have...
#9

Hi Gary

Yes, the "B" referred to the style of cabinet; in this case, "B" = Baby Grand - which is how Philco referred to its cathedrals and tombstones back then. The terms "cathedral" and "tombstone" did not come into general use until decades later, as people like us began to collect these radios.

The sticker on the back of the chassis will read "CHASSIS TYPE 84" without mentioning the cabinet style.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
What do I have... - by Kico - 12-26-2010, 08:54 AM
Re: What do I have... - by Ron Ramirez - 12-26-2010, 09:08 AM
Re: What do I have... - by Kico - 12-26-2010, 01:48 PM
Re: What do I have... - by 7estatdef - 12-26-2010, 04:54 PM
Re: What do I have... - by Kico - 12-28-2010, 10:13 AM
Re: What do I have... - by Ron Ramirez - 12-28-2010, 01:16 PM
Re: What do I have... - by Kico - 12-28-2010, 06:33 PM
Re: What do I have... - by gary rabbitt - 01-06-2011, 01:52 AM
Re: What do I have... - by Ron Ramirez - 01-06-2011, 01:10 PM
Re: What do I have... - by gary rabbitt - 01-06-2011, 01:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4932 online users. [Complete List]
» 2 Member(s) | 4930 Guest(s)
AvatarAvatar

>