Speaker Test Replacement

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Speaker Test Replacement

Robbie Roberts
Member

Posts: 147
Threads: 28
Joined: Nov 2005

02-23-2006, 04:55 PM

Cool- an alternate method! So I could theorhetically get just the field coil as a spare, disconnect the speaker entirely, put the spare field coil in the circuit, and attach the speaker leads to the HK tracer, or put resistance in its place, and use the meter to measure the strength of the output, instead of hurting my ears?

Scott

Old Cars, Old Radios, Old Pipes and Young Women... What more is there?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Speaker Test Replacement - by Robbie Roberts - 02-18-2006, 12:16 AM

[No subject] - by Terry Burns - 02-18-2006, 02:45 PM

[No subject] - by Robbie Roberts - 02-18-2006, 09:22 PM

[No subject] - by Terry Burns - 02-19-2006, 03:09 PM

[No subject] - by Robbie Roberts - 02-19-2006, 03:44 PM

[No subject] - by Poston Drake - 02-23-2006, 04:05 PM

[No subject] - by Robbie Roberts - 02-23-2006, 04:55 PM

[No subject] - by Poston Drake - 02-25-2006, 01:24 AM

Re: Speaker Test Replacement - by dcastor - 08-06-2011, 10:03 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 4148 online users. [Complete List]
» 2 Member(s) | 4146 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me