1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Parts list or Volume Pot Value
JGatewood
Junior Member
**
Posts: 17
Threads: 5
Joined: Dec 2010
#6

01-08-2011, 10:03 AM
Sorry for the long delay, Just got back to a point to work on it again. I measured the 2 Outside terminals and all the way up, it measures approx. 150 Ohms. All the way down it measures approx 1 Meg. Ohms. About 9/10ths turned all the way up it jumps to the Kilo Ohms range (approx. 49.2Kilo Ohms) before jumping immediately to the 150 Ohms reading. This is consistent and can be duplicated every time.
Jerry Gatewood
Philco 41-280 (121)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Parts list or Volume Pot Value - by JGatewood - 12-27-2010, 10:11 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 12-27-2010, 11:15 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 12-28-2010, 06:29 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-08-2011, 10:03 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-09-2011, 06:02 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-09-2011, 09:50 PM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-10-2011, 03:48 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-10-2011, 06:04 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-10-2011, 06:12 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-13-2011, 06:02 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-13-2011, 05:06 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-14-2011, 06:21 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-14-2011, 05:44 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-30-2011, 02:10 PM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-30-2011, 03:16 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-30-2011, 04:20 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently 4350 online users. [Complete List]
» 3 Member(s) | 4347 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration